參數資料
型號： DS87C550-QCL+
廠商： Maxim Integrated Products
文件頁數： 11/49頁
文件大?。?/td> 0K
描述： IC MCU EPROM ADC/PWM HS 68-PLCC
標準包裝： 18
系列： 87C
核心處理器： 8051
芯體尺寸： 8-位
速度： 33MHz
連通性： EBI/EMI，SIO，UART/USART
外圍設備： 電源故障復位，PWM，WDT
輸入/輸出數： 55
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： OTP
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
數據轉換器： A/D 6x10b
振蕩器型： 外部
工作溫度： 0°C ~ 70°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 管件
DS87C550 EPROM High-Speed Microcontroller with ADC and PWM
19 of 49
Alternately, software can prevent an undesired exit from PMM by entering a low priority interrupt service
level before entering PMM. This will prevent other low priority interrupts from causing a Switchback.
Status also contains information about the state of the serial ports. Serial Port Zero Receive Activity
(SPRA0; STATUS.0) indicates a serial word is being received on Serial Port 0 when this bit is set to a 1.
Serial Port Zero Transmit Activity (SPTA0; STATUS.1) indicates that the serial port is still shifting out a
serial transmission. STATUS.2 (SPRA1) and STATUS.3 (SPTA1) provide the same information for
Serial Port 1, respectively. While one of these bits is set, hardware prohibits software from entering PMM
(CD1 & CD0 are write-protected) since this would corrupt the corresponding serial transmissions.
IDLE MODE
Setting the LSB of the Power Control register (PCON.0) invokes the Idle mode. Idle will leave internal
clocks, serial ports and timers running. Power consumption drops because memory is not being accessed
and instructions are not being executed. Since clocks are running, the Idle power consumption is a
function of crystal frequency. It should be approximately of the operational power at a given
frequency. The CPU can exit the Idle state with any interrupt or a reset. Idle is available for backward
software compatibility. However, due to improvements over the original architecture, the processor’s
power consumption can be reduced to below Idle levels by invoking Power Management Mode (PMM)
and running NOPs.
STOP MODE
Setting bit 1 of the Power Control register (PCON.1) invokes the Stop mode. Stop mode is the lowest
power state (besides power-off) since it turns off all internal clocking. The ICC of a standard Stop mode is
typically 1
mA (but is specified in the Electrical Specifications). All processor operation ceases at the end
of the instruction that sets PCON.1. The CPU can exit Stop mode from an external interrupt or a reset
condition. Internally generated interrupts (timer, serial port, etc.) are not useful since they require
clocking activity.
BAND-GAP SELECT
The DS87C550 provides two enhancements to the Stop mode. As described below, the DS87C550
provides a band-gap reference to determine Power-fail Interrupt and Reset thresholds. The default state is
that the band-gap reference is off while in Stop mode. This mode allows the extremely low-power state
mentioned above. A user can optionally choose to have the band-gap enabled during Stop mode. With the
band-gap reference enabled, PFI and Power-fail Reset are functional and are valid means for leaving Stop
mode. This allows software to detect and compensate for a brownout or power supply sag, even when in
Stop mode.
In Stop mode with the band-gap enabled, ICC will be approximately 100
mA compared with 1mA with the
band-gap off. If a user does not require a Power-fail Reset or Interrupt while in Stop mode, the band-gap
can remain disabled. Only the most power-sensitive applications should turn off the band-gap, as this
results in an uncontrolled power-down condition.
The control of the band-gap reference is located in the Ring Oscillator Control Register (RCON). Setting
BGS (RCON.0) to a 1 will keep the band-gap reference enabled during Stop mode. The default or reset
condition is with the bit at a logic 0. This results in the band-gap being off during Stop mode. Note that
this bit has no control of the reference during full power, PMM, or Idle modes.
相關PDF資料
PDF描述
DS89C450-ENL IC MCU FLASH 64KB 33MHZ 44-TQFP
DS9034PCI IC SRAM NV TIMEKEEPING POWERCAP
DS9034PCX PCM W/CRYSTAL NV SRAM SNAP-ON
DS9092L+ IBUTTON PROBE PANEL MOUNT W/LED
DS9092T# IBTN PROBE W/TACTILE FEEDBACK
相關代理商/技術參數
參數描述
DS87C550-QCL+ 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
DS87C550-QCW 制造商:Maxim Integrated Products 功能描述:DS87C550 WAIVERED FOR LS & MARKING - Rail/Tube
DS87C550-QNL 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
DS88 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
DS8800 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual Voltage Level Translator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*