參數資料
型號： DSP56F805E
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： 16-bit Digital Signal Controllers
中文描述： 16位數字信號控制器
文件頁數： 19/56頁
文件大?。?/td> 415K
代理商： DSP56F805E
JTAG/OnCE
56F805 Technical Data, Rev. 15
Freescale Semiconductor
19
2.14 JTAG/OnCE
Part 3 Specifications
3.1 General Characteristics
The 56F805 is fabricated in high-density CMOS with 5V-tolerant TTL-compatible digital inputs. The term
“5V-tolerant” refers to the capability of an I/O pin, built on a 3.3V-compatible process technology, to
withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices
designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5V-compatible
I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V
±
10% during
Table 2-18 JTAG/On-Chip Emulation (OnCE) Signals
No. of
Pins
Signal
Name
Signal
Type
State During
Reset
Signal Description
1
TCK
Input
(Schmitt)
Input, pulled
low internally
Test Clock Input
—This input pin provides a gated clock to
synchronize the test logic and shift serial data to the JTAG/OnCE
port. The pin is connected internally to a pull-down resistor.
1
TMS
Input
(Schmitt)
Input, pulled
high internally
Test Mode Select Input
—This input pin is used to sequence the
JTAG TAP controller’s state machine. It is sampled on the rising
edge of TCK and has an on-chip pull-up resistor.
Note:
Always tie the TMS pin to V
DD
through a 2.2K resistor.
1
TDI
Input
(Schmitt)
Input, pulled
high internally
Test Data Input
—This input pin provides a serial input data stream
to the JTAG/OnCE port. It is sampled on the rising edge of TCK and
has an on-chip pull-up resistor.
1
TDO
Output
Tri-stated
Test Data Output
—This tri-statable output pin provides a serial
output data stream from the JTAG/OnCE port. It is driven in the
Shift-IR and Shift-DR controller states, and changes on the falling
edge of TCK.
1
TRST
Input
(Schmitt)
Input, pulled
high internally
Test Reset
—As an input, a low signal on this pin provides a reset
signal to the JTAG TAP controller. To ensure complete hardware
reset, TRST should be asserted at power-up and whenever RESET
is asserted. The only exception occurs in a debugging environment
when a hardware device reset is required and it is necessary not to
reset the OnCE/JTAG module. In this case, assert RESET, but do
not assert TRST.
Note:
is to be used in a debugging environment, TRST may be tied to V
SS
through a 1K resistor.
For normal operation, connect TRST directly to V
SS
. If the design
1
DE
Output
Output
Debug Event
—DE provides a low pulse on recognized debug
events.
相關PDF資料
PDF描述
DSP56F805FV80E 16-bit Digital Signal Controllers
DSP56F805 16-bit Hybrid Controller(16位混合控制器)
DSP56F807PY80E 16-bit Digital Signal Controllers
DSP56F807VF80E 16-bit Digital Signal Controllers
DSP56F807 16-bit Hybrid Controller(16位混合控制器)
相關代理商/技術參數
參數描述
DSP56F805EVM 功能描述:開發板和工具包 - 其他處理器 Evaluation Kit For DSP56F805 RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
DSP56F805EVMUM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56F805 Evaluation Module Hardware User＇s Manual
DSP56F805FV80 功能描述:數字信號處理器和控制器 - DSP, DSC 80Mhz/ 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56F805FV80E 功能描述:數字信號處理器和控制器 - DSP, DSC 80Mhz/40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56F805FV80E 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*