- 您現在的位置：買賣IC網 > PDF目錄3856 > DSPIC30F2010-20I/SO (Microchip Technology)IC DSPIC MCU/DSP 12K 28SOIC PDF資料下載
參數資料
| 型號： | DSPIC30F2010-20I/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 13/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSPIC MCU/DSP 12K 28SOIC |
| 產品培訓模塊： | dsPIC30F Quadrature Encoder Interface Serial Communications using dsPIC30F I2C Serial Communications using dsPIC30F SPI Serial Communications using dsPIC30F UART dsPIC30F 12 bit ADC - Part 2 dsPIC30F Addressing Modes - Part 1 dsPIC30F Architecture - Part 1 dsPIC30F DSP Engine & ALU dsPIC30F Interrupts dsPIC30F Motor Control PWM dsPIC Timers Asynchronous Stimulus dsPIC30F Addressing Modes - Part 2 dsPIC30F Architecture - Part 2 dsPIC30F 12-bit ADC Part 1 |
| 標準包裝： | 27 |
| 系列： | dsPIC™ 30F |
| 核心處理器： | dsPIC |
| 芯體尺寸： | 16-位 |
| 速度： | 20 MIPS |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 高級欠壓探測/復位，電機控制 PWM，QEI，POR，PWM，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 12KB（4K x 24） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 1K x 8 |
| RAM 容量： | 512 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 數據轉換器： | A/D 6x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 管件 |
| 配用： | XLT28SO-1-ND - SOCKET TRANSITION 28SOIC 300MIL |
| 其它名稱： | DSPIC30F2010-20I/SOG DSPIC30F201020IS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
dsPIC30F Flash Programming Specification
DS70102K-page 20
2010 Microchip Technology Inc.
6.0
OTHER PROGRAMMING
FEATURES
6.1
Erasing Memory
Memory is erased by using an ERASEB, ERASED or
ERASEP command, as detailed in Section 8.5
“Command Descriptions”. Code memory can be
erased by row using ERASEP. Data EEPROM can be
erased by row using ERASED. When memory is erased,
the affected memory locations are set to ‘1’s.
ERASEB provides several Bulk Erase options.
Performing a Chip Erase with the ERASEB command
clears all code memory, data EEPROM and code
protection registers. Alternatively, ERASEB can be used
to selectively erase either all code memory or data
EEPROM. Erase options are summarized in Table 6-1.
TABLE 6-1:
ERASE OPTIONS
Command
Affected Region
ERASEB
Entire chip(1) or all code memory or all
data EEPROM, or erase by segment
ERASED
Specified rows of data EEPROM
ERASEP(2)
Specified rows of code memory
Note 1: The system operation Configuration
registers and device ID registers are not
erasable.
2: ERASEP cannot be used to erase code-
protect Configuration bits. These bits must
be erased using ERASEB.
6.2
Modifying Memory
Instead
of
bulk-erasing
the
device
before
programming, it is possible that you may want to modify
only a section of an already programmed device. In this
situation, Chip Erase is not a realistic option.
Instead, you can erase selective rows of code memory
and data EEPROM using ERASEP and ERASED,
respectively. You can then reprogram the modified
rows with the PROGP and PROGD command pairs. In
these cases, when code memory is programmed,
single-panel programming must be specified in the
PROGP command.
For modification of Advanced Code Protection bits for
a particular segment, the entire chip must first be
erased with the ERASEB command. Alternatively, on
devices that support Advanced Security, individual
segments (code and/or data EEPROM) may be
erased, by suitably changing the MS (Memory Select)
field in the ERASEB command. The code-protect
Configuration bits can then be reprogrammed using the
PROGC command.
Note:
If read or write code protection is enabled
for a segment, no modifications can be
made to that segment until code
protection is disabled. Code protection
can only be disabled by performing a Chip
Erase or by performing a Segment Erase
operation for the required segment.
6.3
Reading Memory
The READD command reads the data EEPROM,
Configuration bits and device ID of the device. This
command only returns 16-bit data and operates on
16-bit registers. READD can be used to return the
entire contents of data EEPROM.
The READP command reads the code memory of the
device. This command only returns 24-bit data packed
as described in Section 8.3 “Packed Data Format”.
READP can be used to read up to 32K instruction words
of code memory.
Note:
Reading an unimplemented memory
location
causes
the
programming
executive to reset. All READD and READP
commands must specify only valid
memory locations.
6.4
Programming Executive Software
Version
At times, it may be necessary to determine the version
of programming executive stored in executive memory.
The QVER command performs this function. See
Section 8.5.11 “QVER Command” for more details
about this command.
6.5
Data EEPROM Information in the
Hexadecimal File
To allow portability of code, the programmer must read
the data EEPROM information from the hexadecimal
file. If data EEPROM information is not present, a
simple warning message should be issued by the
programmer. Similarly, when saving a hexadecimal file,
all data EEPROM information must be included. An
option to not include the data EEPROM information can
be provided.
Microchip Technology Inc. believes that this feature is
important for the benefit of the end customer.
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA16-16MI | IC AVR MCU 16K 16MHZ IND 44-QFN |
| PIC24FJ32GA104-I/PT | IC MCU 16BIT 32KB FLASH 44TQFP |
| DSPIC30F2012-30I/ML | IC DSPIC MCU/DSP 12K 28QFN |
| ATMEGA16-16PI | IC AVR MCU 16K 16MHZ IND 40-DIP |
| ATMEGA128-16MI | IC AVR MCU 128K 16MHZ IND 64-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPIC30F2010-20ISP | 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-30I | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-bit Digital Signal Controllers |
| dsPIC30F2010-30I/MM | 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU DSP 28LD 20MIPS 12KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-30I/MMG | 功能描述:數字信號處理器和控制器 - DSP, DSC 16bit Signal Cntrlr Lead Free Package RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-30I/SO | 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 12KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。