- 您現在的位置：買賣IC網 > PDF目錄3862 > DSPIC30F2011-30I/SO (Microchip Technology)IC DSPIC MCU/DSP 12K 18SOIC PDF資料下載
參數資料
| 型號： | DSPIC30F2011-30I/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 40/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSPIC MCU/DSP 12K 18SOIC |
| 產品培訓模塊： | Serial Communications using dsPIC30F I2C Serial Communications using dsPIC30F SPI Serial Communications using dsPIC30F UART dsPIC30F 12 bit ADC - Part 2 dsPIC30F Addressing Modes - Part 1 dsPIC30F Architecture - Part 1 dsPIC30F DSP Engine & ALU dsPIC30F Interrupts dsPIC30F Motor Control PWM dsPIC Timers Asynchronous Stimulus dsPIC30F Addressing Modes - Part 2 dsPIC30F Architecture - Part 2 dsPIC30F 12-bit ADC Part 1 |
| 標準包裝： | 42 |
| 系列： | dsPIC™ 30F |
| 核心處理器： | dsPIC |
| 芯體尺寸： | 16-位 |
| 速度： | 30 MIP |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 12 |
| 程序存儲器容量： | 12KB（4K x 24） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 數據轉換器： | A/D 8x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 18-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 管件 |
| 產品目錄頁面： | 650 (CN2011-ZH PDF) |
| 配用： | XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MIL AC30F005-ND - MODULE SCKT DSPIC30F 18DIP/SOIC DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE |
| 其它名稱： | DSPIC30F201130ISO |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
2010 Microchip Technology Inc.
DS70102K-page 45
dsPIC30F Flash Programming Specification
11.8
Writing Code Memory
The procedure for writing code memory is similar to the
procedure for clearing the Configuration registers,
except that 32 instruction words are programmed at a
time. To facilitate this operation, working registers
W0:W5 are used as temporary holding registers for the
data to be programmed.
Table 11-8 shows the ICSP programming details,
including the serial pattern with the ICSP command
code, which must be transmitted Least Significant bit
first using the PGC and PGD pins (see Figure 11-2). In
Step 1, the Reset vector is exited. In Step 2, the
NVMCON register is initialized for single-panel
programming of code memory. In Step 3, the 24-bit
starting destination address for programming is loaded
into the TBLPAG register and W7 register. The upper
byte of the starting destination address is stored to
TBLPAG, while the lower 16 bits of the destination
address are stored to W7.
To minimize the programming time, the same packed
instruction format that the programming executive uses
is utilized (Figure 8-2). In Step 4, four packed
instruction words are stored to working registers
W0:W5 using the MOV instruction and the read pointer
W6 is initialized. The contents of W0:W5 holding the
packed instruction word data is shown in Figure 11-4.
In Step 5, eight TBLWT instructions are used to copy the
data from W0:W5 to the write latches of code memory.
Since code memory is programmed 32 instruction
words at a time, Steps 4 and 5 are repeated eight times
to load all the write latches (Step 6).
After the write latches are loaded, programming is
initiated by writing to the NVMKEY and NVMCON
registers in Steps 7 and 8. In Step 9, the internal PC is
reset to 0x100. This is a precautionary measure to
prevent the PC from incrementing into unimplemented
memory when large devices are being programmed.
Lastly, in Step 10, Steps 2-9 are repeated until all of
code memory is programmed.
FIGURE 11-5:
PACKED INSTRUCTION
WORDS IN W0:W5
15
8
7
0
W0
lsw0
W1
MSB1
MSB0
W2
lsw1
W3
lsw2
W4
MSB3
MSB2
W5
lsw3
TABLE 11-8:
SERIAL INSTRUCTION EXECUTION FOR WRITING CODE MEMORY
Command
(Binary)
Data
(Hexadecimal)
Description
Step 1: Exit the Reset vector.
0000
040100
000000
GOTO 0x100
NOP
Step 2: Set the NVMCON to program 32 instruction words.
0000
24001A
883B0A
MOV
#0x4001, W10
MOV
W10, NVMCON
Step 3: Initialize the write pointer (W7) for TBLWT instruction.
0000
200xx0
880190
2xxxx7
MOV
#<DestinationAddress23:16>, W0
MOV
W0, TBLPAG
MOV
#<DestinationAddress15:0>, W7
Step 4: Initialize the read pointer (W6) and load W0:W5 with the next 4 instruction words to program.
0000
2xxxx0
2xxxx1
2xxxx2
2xxxx3
2xxxx4
2xxxx5
MOV
#<LSW0>, W0
MOV
#<MSB1:MSB0>, W1
MOV
#<LSW1>, W2
MOV
#<LSW2>, W3
MOV
#<MSB3:MSB2>, W4
MOV
#<LSW3>, W5
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LF87-I/P | IC MCU FLASH 4KX14 EEPROM 18DIP |
| PIC16C711-20/P | IC MCU OTP 1KX14 A/D 18DIP |
| SFW30R-1STE1 | SFW30R-1STE1-FFC/FPC CONN |
| SFW25R-1STE1 | SFW25R-1STE1-FFC/FPC CONN |
| SFW14R-2STE1 | SFW14R-2STE1-FFC/FPC CONN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPIC30F2011A20E/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2011A-20E/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2011A20E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2011A-20E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2011A20E/SO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
發布緊急采購，3分鐘左右您將得到回復。