參數資料
型號： DT28F320S3-120
廠商： Intel Corp.
英文描述： 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
中文描述： 字寬FlashFile⑩Memory系列
文件頁數： 27/52頁
文件大?。?/td> 1262K
代理商： DT28F320S3-120
E
This two-step command sequence of setup followed
by execution ensures that block contents are not
accidentally erased. An invalid Full Chip Erase
command sequence will result in both Status
Register bits SR.4 and SR.5 being set to 1. Also,
reliable full chip erasure can only occur when
V
CC
= V
CC1/2
and V
PP
= V
PPH1/2
.
In the absence of
these voltages, block contents are protected
against erasure.
If full chip erase is attempted while
V
PP
≤
V
PPLK
, SR.3 and SR.5 will be set to 1.
When
WP# = V
IL
, only unlocked blocks are erased.
Full
chip erase cannot be suspended.
28F160S3, 28F320S3
27
ADVANCE INFORMATION
4.8
Write to Buffer Command
To program the flash device via the write buffers, a
Write to Buffer command sequence is initiated. A
variable number of bytes or words, up to the buffer
size, can be written into the buffer and programmed
to the flash device. First, the Write to Buffer setup
command is issued along with the Block Address.
At this point, the eXtended Status Register
information is loaded and XSR.7 reverts to the
“buffer available” status. If XSR.7 = 0, no write
buffer is available. To retry, continue monitoring
XSR.7 by issuing the Write to Buffer setup
command with the Block Address until XSR.7 = 1.
When XSR.7 transitions to a “1,” the buffer is ready
for loading.
Now a Word/Byte count is issued at an address
within the block. On the next write, a device start
address is given along with the write buffer data.
For maximum programming performance and lower
power, align the start address at the beginning of a
Write Buffer boundary. Subsequent writes must
supply additional device addresses and data,
depending on the count. All subsequent addresses
must lie within the start address plus the count.
After the final buffer data is given, a Write Confirm
command is issued. This initiates the WSM to begin
copying the buffer data to the flash memory. If a
command other than Write Confirm is written to the
device, an “Invalid Command/Sequence” error will
be generated and Status Register bits SR.5 and
SR.4 will be set to “1.” For additional buffer writes,
issue another Write to Buffer setup command and
check XSR.7. The write buffers can be loaded while
the WSM is busy as long as XSR.7 indicates that a
buffer is available. Refer to Figure 7 for the Write to
Buffer flowchart.
If an error occurs while writing, the device will stop
programming, and Status Register bit SR.4 will be
set to a “1” to indicate a program failure. Any time a
media failure occurs during a program or an erase
(SR.4 or SR.5 is set), the device will not accept any
more Write to Buffer commands. Additionally, if the
user attempts to write past an erase block boundary
with a Write to Buffer command, the device will
abort programming. This will generate an “Invalid
Command/Sequence” error and Status Register bits
SR.5 and SR.4 will be set to “1.” To clear SR.4
and/or SR.5, issue a Clear Status Register
command.
Reliable buffered programming can only occur
when V
CC
= V
CC1/2
and V
= V
PPH1/2
. If
programming is attempted while V
,
Status Register bits SR.4 and SR.5 will be set to
“1.” Programming attempts with invalid V
and V
voltages produce spurious results and should not
be attempted. Finally, successful programming
requires that the corresponding Block Lock-Bit be
cleared, or WP# = V
IH
. If a buffered write is
attempted when the corresponding Block Lock-Bit
is set and WP# = V
IL
, SR.1 and SR.4 will be set to
“1.”
4.9
Byte/Word Program Commands
Byte/Word programming is executed by a two-cycle
command sequence. Byte/Word Program setup
(standard 40H or alternate 10H) is written, followed
by a second write that specifies the address and
data (latched on the rising edge of WE#). The WSM
then takes over, controlling the program and verify
algorithms internally. After the write sequence is
written, the device automatically outputs Status
Register data when read. The CPU can detect the
completion of the program event by analyzing STS
in level RY/BY# mode or Status Register bit SR.7.
When programming is complete, Status Register bit
SR.4 should be checked. If a programming error is
detected, the Status Register should be cleared.
The internal WSM verify only detects errors for “1”s
that do not successfully program to “0”s. The CUI
remains in read Status Register mode until it
receives another command. Refer to Figure 8 for
the Word/Byte Program flowchart.
Also, Reliable byte/word programming can only
occur when V
CC
= V
CC1/2
and V
PP
= V
PPH1/2
.
In the
absence of this high voltage, contents are protected
against programming.
If a byte/word program is
相關PDF資料
PDF描述
DT28F160S3-120 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
dt31-2025at Telecommunication HDSL Transformer
DT31-2026AT Telecommunication HDSL Transformer
DT31-2031AT Telecommunication HDSL Transformer
DT31-2032AT Telecommunication HDSL Transformer
相關代理商/技術參數
參數描述
DT28F320S3-140 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:WORD-WIDE FlashFile MEMORY FAMILY
DT28F640J5-150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|4MX16/8MX8|CMOS|SOP|56PIN|PLASTIC
DT28F640J5A-150 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:5 Volt Intel StrataFlash? Memory
DT28F800F3B120 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:FAST BOOT BLOCK FLASH MEMORY FAMILY 8 AND 16 MBIT
DT28F800F3B95 制造商:Intel 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*