- 您現在的位置：買賣IC網 > PDF目錄10585 > EL4511CUZ-T7A (Intersil)IC VID SYNC SEPARATR HDTV 24QSOP PDF資料下載
參數資料
| 型號： | EL4511CUZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VID SYNC SEPARATR HDTV 24QSOP |
| 標準包裝： | 250 |
| 類型： | 同步分離器 |
| 應用： | HDTV，投影儀，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
16
FN7009.8
November 12, 2010
Timing Diagram 5 - 720p Standard with Filter in Circuit
Description of Operation
The EL4511 has 3 modes of operation. The first is default
mode with pins 1 and 24 connected to ground with 10K.
Second is using pins 1 and 24 to provide simple mode
control. The third is using the serial port to use a crystal or a
clock into XTALN pin 24 to determine the video sync rate
and/or more extensive mode control.
The EL4511 incorporates the following functional blocks:
Analog I/Ps, processing, and slicing
Signal source and polarity detector
Signal & H rate acquisition block
Advanced sync separator which will detect both
conventional and tri-level sync signals
Video lock and level indicators
Reference counter
Computer and control interface
Analog I/Ps, Processing, and Slicing
The EL4511 has three I/P pins which may be connected to a
source of external sync signals.
For YPrPb or RGB applications, Y or G should be connected
to SYNCIN. For applications with separate horizontal and
vertical sync inputs, these should be connected to HIN and
VERTIN, respectively. (HIN may also be used for composite
sync without video.)
Composite video input signals should be connected to
SYNCIN. This should be AC coupled from a low impedance
source. The input resistance is in the order of 100k
Ω. After H
lock is obtained, this signal will be “soft clamped” (5k
Ω) to
approximately 20% of the VCCA1 voltage.
In the default mode, the clamping action ensures that the
correct slicing levels will be used throughout the field.
(Serial Mode) This operation can be modified through
Register 9. The soft clamp can be disabled by setting bit 3 to
Hi. Setting bit 1 to high will disconnect the input bias
network.
Once the acquisition process is complete (see below for
description), the slice level will be adaptive. The sync signal
is measured from sync tip to blanking level; (Tri-level is
measured between negative and positive sync tips). The
slice level is then set to 50% of these levels.
(Serial Mode) It is possible to force the slicing level to
remain at the fixed level of 78mV above the sync tip;
Register 2, bit 5 is set High to do this. This can help when
dealing with signal that have bursts of noise, or formats that
have signals that will modify the sync amplitude
measurement process.
VGA type of signals will be connected to the HIN and
VERTIN pins (use HIN for combined H & V). These are DC
coupled signals; they will be sliced at a fixed level of
approximately 1.4V. These inputs may be any combination
of positive and negative polarities; the EL4511 will invert as
required to keep the outputs in the correct polarity. (Serial
Mode) This polarity correction process may be modified with
Register 4 bits 3:0.
Signal and Horizontal Rate Acquisition Block
On power-up, if both HIN and SYNCIN are enabled; the
EL4511 will slice the SYNCIN input at 78mV above the
negative sync tip level and monitor the sliced signal for up to
320s. If a periodic signal within the specified frequency
limits is found to be present, this is assumed to be the
horizontal frequency. If no signal is found, the EL4511 will
switch to slice and monitor the HIN input at a TTL level. The
EL4511 will continue to monitor these two signals in turn until
an appropriate signal is detected.
If only one of HIN and SYNCIN is enabled, the EL4511 will
continuously monitor the selected signal until an appropriate
signal is detected; this will give a shorter lock time where
only one type of signal is used. At this point, the rate
acquisition oscillator lock process (to the H rate signal) will
begin.
This waveform shows
the output jitter present
on the HOUT signal. The
oscilloscope is triggered
from the positive
reference edge of the
composite sync output.
EL4511
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JTK-MY-F4 | CONVERTER MOD DC/DC 40V 50W |
| VE-27M-IW-F2 | CONVERTER MOD DC/DC 10V 100W |
| SF6282-4PG-520 | CONN PLUG 4POS CABLE PIN |
| T 3650 001 | CONN CIR MALE 14POS CBL MNT |
| ISL59603IRZ-T7 | IC VIDEO EQUALIZER 20-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL4511CUZ-T7S2705 | 制造商:Intersil Corporation 功能描述:CISCO, EL4511CUZ-T7 W/CONTAINER LABELING - Tape and Reel |
| EL452(TA)-VG | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:4 PIN SOP HIGH VOLTAGE DARLINGTON |
| EL452(TB)-VG | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:4 PIN SOP HIGH VOLTAGE DARLINGTON |
| EL452-G | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:4 PIN SOP HIGH VOLTAGE DARLINGTON |
| EL4543 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Differential Twisted-Pair Driver with Common-Mode Sync Encoding |
發布緊急采購，3分鐘左右您將得到回復。