參數資料
型號： EPCS1SI8
廠商： Altera
文件頁數： 19/40頁
文件大?。?/td> 0K
描述： IC CONFIG DEVICE 1MBIT 8-SOIC
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 100
系列： EPCS
可編程類型： 系統內可編程
存儲容量： 1Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOIC
包裝： 管件
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1241-5
P
age
2
6
E
PCS
D
e
vi
c
e
M
e
m
o
ry
A
cce
ss
S
er
ial
C
o
nf
ig
ur
at
io
n
(
E
P
C
S
)D
evi
ces
D
at
ashee
t
Janu
ar
y201
4
A
lte
ra
C
o
rp
or
at
io
n
Figure 15 shows the instruction sequence of the write bytes operation.
Erase Bulk Operation
The erase bulk operation code is b'1100 0111 and it lists the MSB first. This operation sets all the memory bits to 1 or 0xFF.
Similar to the write bytes operation, you must execute the write enable operation before the erase bulk operation so that the
write enable latch bit in the status register is set to 1.
You can implement the erase bulk operation by driving the nCS signal low and then shifting in the erase bulk operation code on
the ASDI pin. The nCS signal must be driven high after the eighth bit of the erase bulk operation code has been latched in.
The device initiates a self-timed erase bulk cycle immediately after the nCS signal is driven high. For more information about
the self-timed erase bulk cycle time, refer to the tEB value in Table 16 on page 29.
You must account for this delay before accessing the memory contents. Alternatively, you can check the write in progress bit in
the status register by executing the read status operation while the self-timed erase cycle is in progress. The write in progress
bit is set to 1 during the self-timed erase cycle and 0 when it is complete. The write enable latch bit in the status register is reset
to 0 before the erase cycle is complete.
Figure 15. Write Bytes Operation Timing Diagram (1)
Notes to Figure 15:
(1) Use the erase sector operation or the erase bulk operation to initialize the memory bytes of the EPCS devices to all 1 or 0xFF before implementing the write bytes operation.
(2) Address bit A[23] is a don't-care bit in the EPCS64 device. Address bits A[23..21] are don't-care bits in the EPCS16 device. Address bits A[23..19] are don't-care bits in the EPCS4 device. Address
bits A[23..17] are don't-care bits in the EPCS1 device.
(3) For .rpd files, write the LSB of the data byte first.
nCS
DCLK
ASDI
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
2072 2073 2074 2075 2076 2077 2078 2079
Operation Code
24-Bit Address (2)
23
22
21
3
2
1
0
765
4
MSB
MSB (3)
Data Byte 1
Data Byte 2
Data Byte 256
321
0
765
4
7
65
4
321
0
321
0
相關PDF資料
PDF描述
EBC10DREF-S13 CONN EDGECARD 20POS .100 EXTEND
GRM2165C2A161JA01D CAP CER 160PF 100V 5% NP0 0805
RMC05DRYI CONN EDGECARD 10POS DIP .100 SLD
ABB45DHRR CONN CARD EXTEND 90POS .050"
TAS476K020P1F-F CAP TANT 47UF 20V 10% AXIAL
相關代理商/技術參數
參數描述
EPCS1SI8N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPCS250 制造商:Electrolube 功能描述:COATING MASK PEELABLE 250 制造商:Electrolube 功能描述:COATING MASK, PEELABLE 250
EPCS2PC1 制造商:Switchcraft 功能描述:
EPCS4 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Serial Configuration Devices
EPCS4SI8 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 4Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*