參數資料
型號： EPCS1SI8
廠商： Altera
文件頁數： 30/40頁
文件大?。?/td> 0K
描述： IC CONFIG DEVICE 1MBIT 8-SOIC
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 100
系列： EPCS
可編程類型： 系統內可編程
存儲容量： 1Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOIC
包裝： 管件
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1241-5
Page 36
Pin Information
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Table 23 lists the pin description of the EPCS device.
Figure 23 shows the layout recommendation for vertical migration from the EPCS1
device to the EPCS128 device.
Table 23. EPCS Device Pin Description
Pin
Name
Pin Number
in 8-Pin
SOIC
Package
Pin Number
in 16-Pin
SOIC
Package
Pin Type
Description
DATA
2
8
Output
The DATA output signal transfers data serially out of the EPCS device
to the FPGA during the read operation or configuration. During the
read operation or configuration, the EPCS device is enabled by pulling
the nCS signal low. The DATA signal transitions on the falling edge of
the DCLK signal.
ASDI
5
15
Input
The ASDI signal is used to transfer data serially into the EPCS device.
This pin are also receiving data that are programmed into the EPCS
device. Data is latched on the rising edge of the DCLK signal.
nCS
1
7
Input
The nCS signal toggles at the beginning and the end of a valid
instruction. When this signal goes high, the device is deselected and
the DATA pin is tri-stated. When this signal goes low, the device is
enabled and in an active mode. After power up, the EPCS device
requires a falling edge on the nCS signal before the EPCS device
begins any operation.
DCLK
6
16
Input
The FPGA provides the DCLK signal. This signal provides the timing
for the serial interface. The data presented on the ASDI pin is latched
to the EPCS device on the rising edge of the DCLK signal. The data on
the DATA pin changes after the falling edge of the DCLK signal and is
latched into the FPGA on the next falling edge of the DCLK signal.
VCC
3, 7, 8
1, 2, 9
Power
Connect the power pins to a 3.3-V power supply.
GND
4
10
GND
Ground pin.
Figure 23. Layout Recommendation for Vertical Migration from the EPCS1 Device to the EPCS128
Device
Pi
n1
ID
Pin 1 ID
相關PDF資料
PDF描述
EBC10DREF-S13 CONN EDGECARD 20POS .100 EXTEND
GRM2165C2A161JA01D CAP CER 160PF 100V 5% NP0 0805
RMC05DRYI CONN EDGECARD 10POS DIP .100 SLD
ABB45DHRR CONN CARD EXTEND 90POS .050"
TAS476K020P1F-F CAP TANT 47UF 20V 10% AXIAL
相關代理商/技術參數
參數描述
EPCS1SI8N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPCS250 制造商:Electrolube 功能描述:COATING MASK PEELABLE 250 制造商:Electrolube 功能描述:COATING MASK, PEELABLE 250
EPCS2PC1 制造商:Switchcraft 功能描述:
EPCS4 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Serial Configuration Devices
EPCS4SI8 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 4Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*