- 您現在的位置：買賣IC網 > PDF目錄19912 > EPCS1SI8 (Altera)IC CONFIG DEVICE 1MBIT 8-SOIC PDF資料下載
參數資料
| 型號： | EPCS1SI8 |
| 廠商： | Altera |
| 文件頁數： | 21/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONFIG DEVICE 1MBIT 8-SOIC |
| 產品培訓模塊： | Three Reasons to Use FPGA's in Industrial Designs |
| 標準包裝： | 100 |
| 系列： | EPCS |
| 可編程類型： | 系統內可編程 |
| 存儲容量： | 1Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 604 (CN2011-ZH PDF) |
| 其它名稱： | 544-1241-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Page 28
Power and Operation
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Power and Operation
This section describes the power modes, power-on reset (POR) delay, error detection,
and initial programming state of the EPCS devices.
Power Mode
EPCS devices support active and standby power modes. When the nCS signal is low,
the device is enabled and is in active power mode. The FPGA is configured while the
EPCS device is in active power mode. When the nCS signal is high, the device is
disabled but remains in active power mode until all internal cycles are completed,
such as write or erase operations. The EPCS device then goes into standby power
mode. The ICC1 and ICC0 parameters list the VCC supply current when the device is in
active and standby power modes. For more information, refer to Table 21 on page 34.
Power-On Reset
During the initial power-up, a POR delay occurs to ensure the system voltage levels
have stabilized. During the AS configuration, the FPGA controls the configuration
and has a longer POR delay than the EPCS device.
f For more information about the POR delay time, refer to the configuration chapter in
the appropriate device handbook.
Error Detection
During the AS configuration with the EPCS device, the FPGA monitors the
configuration status through the nSTATUS and CONF_DONE pins. If an error condition
occurs, if the nSTATUS pin drives low or if the CONF_DONE pin does not go high, the
FPGA begins reconfiguration by pulsing the nSTATUS and nCSO signals, which controls
the chip select (nCS) pin on the EPCS device.
After an error, the configuration automatically restarts if the Auto-Restart Upon
Frame Error
option is turned on in the Quartus II software. If the option is turned off,
the system must monitor the nSTATUS signal for errors and then pulse the nCONFIG
signal low to restart configuration.
相關PDF資料 |
PDF描述 |
|---|---|
| EBC10DREF-S13 | CONN EDGECARD 20POS .100 EXTEND |
| GRM2165C2A161JA01D | CAP CER 160PF 100V 5% NP0 0805 |
| RMC05DRYI | CONN EDGECARD 10POS DIP .100 SLD |
| ABB45DHRR | CONN CARD EXTEND 90POS .050" |
| TAS476K020P1F-F | CAP TANT 47UF 20V 10% AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPCS1SI8N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPCS250 | 制造商:Electrolube 功能描述:COATING MASK PEELABLE 250 制造商:Electrolube 功能描述:COATING MASK, PEELABLE 250 |
| EPCS2PC1 | 制造商:Switchcraft 功能描述: |
| EPCS4 | 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Serial Configuration Devices |
| EPCS4SI8 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 4Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
發布緊急采購，3分鐘左右您將得到回復。