參數資料
型號： EPCS4SI8
廠商： Altera
文件頁數： 18/40頁
文件大?。?/td> 0K
描述： IC CONFIG DEVICE 4MBIT 8-SOIC
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 100
系列： EPCS
可編程類型： 系統內可編程
存儲容量： 4Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOIC
包裝： 管件
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1243-5
EPCS Device Memory Access
Page 25
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Write Bytes Operation
The write bytes operation code is b'0000 0010 and it lists the MSB first. This
operation allows bytes to be written to the memory. You must execute the write enable
operation before the write bytes operation to set the write enable latch bit in the status
register to 1.
The write bytes operation is implemented by driving the nCS signal low, followed by
the write bytes operation code, three address bytes, and at least one data byte on the
ASDI
pin. If the eight LSBs (A[7..0]) are not all 0, all sent data that goes beyond the
end of the current page is not written into the next page. Instead, this data is written at
the start address of the same page (from the address whose eight LSBs are all 0). You
must ensure the nCS signal is set low during the entire write bytes operation.
If more than 256 data bytes are shifted into the EPCS device with a write bytes
operation, the previously latched data is discarded and the last 256 bytes are written
to the page. However, if less than 256 data bytes are shifted into the EPCS device, they
are guaranteed to be written at the specified addresses and the other bytes of the same
page are not affected.
If your design requires writing more than 256 data bytes to the memory, more than
one page of memory is required. Send the write enable and write bytes operation
codes, followed by three new targeted address bytes and 256 data bytes, before a new
page is written.
The nCS signal must be driven high after the eighth bit of the last data byte has been
latched in. Otherwise, the device does not execute the write bytes operation. The write
enable latch bit in the status register is reset to 0 before the completion of each write
bytes operation. Therefore, the write enable operation must be carried out before the
next write bytes operation.
The device initiates a self-timed write cycle immediately after the nCS signal is driven
high. For more information about the self-timed write cycle time, refer to the tWB value
in Table 16 on page 29. You must account for this amount of delay before another page
of memory is written. Alternatively, you can check the write in progress bit in the
status register by executing the read status operation while the self-timed write cycle
is in progress. The write in progress bit is set to 1 during the self-timed write cycle and
0
when it is complete.
1 You must erase all the memory bytes of the EPCS devices to all 1 or 0xFF before you
implement the write bytes operation. You can erase all the memory bytes by executing
the erase sector operation in a sector or the erase bulk operation throughout the entire
memory.
相關PDF資料
PDF描述
LTC4252-2IMS8#PBF IC CNTRLR HOTSWAP NEGVOLT 8-MSOP
GRM2165C2A131JA01D CAP CER 130PF 100V 5% NP0 0805
RCB92DHRR-S378 EDGECARD EXT PCI64 184PS .050 5V
ECC13DREH-S13 CONN EDGECARD 26POS .100 EXTEND
NCV59301DS28R4G IC REG LDO 2.8V 3A D2PAK-5
相關代理商/技術參數
參數描述
EPCS4SI8N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 4Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPCS4SI8N 制造商:Altera Corporation 功能描述:SEMICONDUCTOR ((NW))
EPCS64 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Serial Configuration Devices
EPCS64SI16N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 64Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPCSC2.5T 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*