參數資料
型號： EPCS4SI8
廠商： Altera
文件頁數： 21/40頁
文件大?。?/td> 0K
描述： IC CONFIG DEVICE 4MBIT 8-SOIC
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 100
系列： EPCS
可編程類型： 系統內可編程
存儲容量： 4Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOIC
包裝： 管件
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1243-5
Page 28
Power and Operation
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Power and Operation
This section describes the power modes, power-on reset (POR) delay, error detection,
and initial programming state of the EPCS devices.
Power Mode
EPCS devices support active and standby power modes. When the nCS signal is low,
the device is enabled and is in active power mode. The FPGA is configured while the
EPCS device is in active power mode. When the nCS signal is high, the device is
disabled but remains in active power mode until all internal cycles are completed,
such as write or erase operations. The EPCS device then goes into standby power
mode. The ICC1 and ICC0 parameters list the VCC supply current when the device is in
active and standby power modes. For more information, refer to Table 21 on page 34.
Power-On Reset
During the initial power-up, a POR delay occurs to ensure the system voltage levels
have stabilized. During the AS configuration, the FPGA controls the configuration
and has a longer POR delay than the EPCS device.
f For more information about the POR delay time, refer to the configuration chapter in
the appropriate device handbook.
Error Detection
During the AS configuration with the EPCS device, the FPGA monitors the
configuration status through the nSTATUS and CONF_DONE pins. If an error condition
occurs, if the nSTATUS pin drives low or if the CONF_DONE pin does not go high, the
FPGA begins reconfiguration by pulsing the nSTATUS and nCSO signals, which controls
the chip select (nCS) pin on the EPCS device.
After an error, the configuration automatically restarts if the Auto-Restart Upon
Frame Error
option is turned on in the Quartus II software. If the option is turned off,
the system must monitor the nSTATUS signal for errors and then pulse the nCONFIG
signal low to restart configuration.
相關PDF資料
PDF描述
LTC4252-2IMS8#PBF IC CNTRLR HOTSWAP NEGVOLT 8-MSOP
GRM2165C2A131JA01D CAP CER 130PF 100V 5% NP0 0805
RCB92DHRR-S378 EDGECARD EXT PCI64 184PS .050 5V
ECC13DREH-S13 CONN EDGECARD 26POS .100 EXTEND
NCV59301DS28R4G IC REG LDO 2.8V 3A D2PAK-5
相關代理商/技術參數
參數描述
EPCS4SI8N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 4Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPCS4SI8N 制造商:Altera Corporation 功能描述:SEMICONDUCTOR ((NW))
EPCS64 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Serial Configuration Devices
EPCS64SI16N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 64Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPCSC2.5T 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*