- 您現在的位置：買賣IC網 > PDF目錄16863 > EV-ADF4360-4EB1Z (Analog Devices Inc)BOARD EVAL FOR ADF4360-4 PDF資料下載
參數資料
| 型號： | EV-ADF4360-4EB1Z |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADF4360-4 |
| 標準包裝： | 1 |
| 主要目的： | 計時，頻率合成器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADF4360-4 |
| 主要屬性： | 帶 VCO 的單路整數-N PLL |
| 次要屬性： | 1.6GHz，200kHz PFD |
| 已供物品： | 板，纜線，CD |
| 其它名稱： | Q7037782 |
ADF4360-4
Data Sheet
Rev. B | Page 22 of 24
PCB DESIGN GUIDELINES FOR CHIP SCALE PACKAGE
The leads on the chip scale package (CP-24) are rectangular.
The printed circuit board pad for these should be 0.1 mm long-
er than the package lead length and 0.05 mm wider than the
package lead width. The lead should be centered on the pad to
ensure that the solder joint size is maximized.
The bottom of the chip scale package has a central thermal pad.
The thermal pad on the printed circuit board should be at least
as large as this exposed pad. On the printed circuit board, there
should be a clearance of at least 0.25 mm between the thermal
pad and the inner edges of the pad pattern to ensure that short-
ing is avoided.
Thermal vias may be used on the printed circuit board thermal
pad to improve thermal performance of the package. If vias are
used, they should be incorporated in the thermal pad at a
1.2 mm pitch grid. The via diameter should be between 0.3 mm
and 0.33 mm, and the via barrel should be plated with 1 ounce
of copper to plug the via.
The user should connect the printed circuit thermal pad to
AGND. This is internally connected to AGND.
OUTPUT MATCHING
There are a number of ways to match the output of the
ADF4360-4 for optimum operation; the most basic is to use a
50 resistor to VVCO. A dc bypass capacitor of 100 pF is con-
nected in series, as shown Figure 21. Because the resistor is not
frequency dependent, this provides a good broadband match.
The output power in this circuit typically gives 4 dBm output
power into a 50 load.
100pF
04438-025
RFOUT
VVCO
50
51
Figure 21. Simple ADF4360-4 Output Stage
A better solution is to use a shunt inductor (acting as an RF
choke) to VVCO. This gives a better match and, therefore, more
output power. Additionally, a series inductor is added after the
dc bypass capacitor to provide a resonant LC circuit. This tunes
the oscillator output and provides approximately 10 dB addi-
tional rejection of the second harmonic. The shunt inductor
needs to be a relatively high value (>40 nH).
Experiments have shown that the circuit shown in Figure 22
provides an excellent match to 50 over the operating
range of the ADF4360-4. This gives approximately 2 dBm
output power across the frequency range of the ADF4360-4.
Both single-ended architectures can be examined using the
EV-ADF4360-4EB1Z evaluation board.
5.1nH
47nH
1.8pF
04438-026
RFOUT
VVCO
50
Figure 22. Optimum ADF4360-4 Output Stage
If the user does not need the differential outputs available on
the ADF4360-4, the user may either terminate the unused out-
put or combine both outputs using a balun. The circuit in Fig-
ure 23 shows how best to combine the outputs.
4.3nH
5.1nH
47nH
5.1nH
1.8pF
10pF
1.8pF
50
4.3nH
RFOUTA
VVCO
RFOUTB
04438-027
Figure 23. Balun for Combining ADF4360-4 RF Outputs
The circuit in Figure 23 is a lumped-lattice-type LC balun. It is
designed for a center frequency of 1.6 GHz and outputs 4.0 dBm
at this frequency. The series 4.3 nH inductor is used to tune out
any parasitic capacitance due to the board layout from each
input, and the remainder of the circuit is used to shift the
output of one RF input by +90° and the second by 90°, thus
combining the two. The action of the 5.1 nH inductor and the
1.8 pF capacitor accomplishes this. The 47 nH is used to pro-
vide an RF choke to feed the supply voltage, and the 10 pF ca-
pacitor provides the necessary dc block. To ensure good RF
performance, the circuits in Figure 22 and Figure 23 are imple-
mented with Coilcraft 0402/0603 inductors and AVX 0402 thin-
film capacitors.
Alternatively, instead of the LC balun shown in Figure 23, both
outputs may be combined using a 180° rat-race coupler.
相關PDF資料 |
PDF描述 |
|---|---|
| V110B15E150BF2 | CONVERTER MOD DC/DC 15V 150W |
| GEC31DRXH-S734 | CONN EDGECARD 62POS DIP .100 SLD |
| TAT-125-1/4-0-STK | HEATSHRINK DUAL WALL 1/4"X4' BLK |
| AFK157M35F24T-F | CAP ALUM 150UF 35V 20% SMD |
| SRR7032-681M | INDUCTOR POWER 680UH .16A SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EV-ADF4360-5EB1Z | 功能描述:時鐘和定時器開發工具 Evaluation Board I.C. RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
| EV-ADF4360-6EB1Z | 功能描述:BOARD EVAL FOR ADS4360-6EBIZ RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EV-ADF4360-7EB1Z | 功能描述:BOARD EVAL FOR ADF4360-7 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EV-ADF4360-8EB1Z | 功能描述:BOARD EVALUATION FOR ADF4360-8 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EV-ADF4360-9EB1Z | 功能描述:BOARD EVAL FOR ADF4360-9 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。