- 您現在的位置：買賣IC網 > PDF目錄17057 > EVAL-AD7192EBZ (Analog Devices Inc)BOARD EVAL FOR AD7192 PDF資料下載
參數資料
| 型號： | EVAL-AD7192EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7192 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 4.8k |
| 數據接口： | SPI?、QSPI?、MICROWIRE? 和 DSP |
| 輸入范圍： | ±VREF/增益 |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7192 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
AD7192
Rev. A | Page 22 of 40
Table 19. Configuration Register Bit Designations
Bit Location
Bit Name
Description
CON23
CHOP
Chop enable bit. When the CHOP bit is cleared, chop is disabled. When the CHOP bit is set, chop is
enabled. When chop is enabled, the offset and offset drift of the ADC are continuously removed.
However, this increases the conversion time and settling time of the ADC. For example, when FS = 96
decimal and the sinc4 filter is selected, the conversion time with chop enabled equals 80 ms and the
settling time equals 160 ms. With chop disabled, higher conversion rates are allowed. For an FS word of
96 decimal and the sinc4 filter selected, the conversion time is 20 ms and the settling time is 80 ms.
However, at low gains, periodic calibrations may be required to remove the offset and offset drift.
CON22, CON21
0
These bits must be programmed with a Logic 0 for correct operation.
CON20
REFSEL
Reference select bits. The reference source for the ADC is selected using these bits.
REFSEL
Reference Voltage
0
External reference applied between REFIN1(+) and REFIN1(
).
1
External reference applied between the P1/REFIN2(+) and P0/REFIN2() pins.
CON19 to CON16
0
These bits must be programmed with a Logic 0 for correct operation.
CON15 to CON8
CH7 to CH0
Channel select bits. These bits are used to select which channels are enabled on the AD7192 (see Table 20).
Several channels can be selected, and the AD7192 automatically sequences them. The conversion on
each channel requires the complete settling time. When performing calibrations or when accessing the
calibration registers, only one channel can be selected.
CON7
BURN
When this bit is set to 1, the 500 nA current sources in the signal path are enabled. When BURN = 0, the
burnout currents are disabled. The burnout currents can be enabled only when the buffer is active and
when chop is disabled.
CON6
REFDET
Enables the reference detect function. When set, the NOREF bit in the status register indicates when the
external reference being used by the ADC is open circuit or less than 0.6 V maximum. The reference
detect circuitry operates only when the ADC is active.
CON5
0
This bit must be programmed with a Logic 0 for correct operation.
CON4
BUF
Enables the buffer on the analog inputs. If cleared, the analog inputs are unbuffered, lowering the
power consumption of the device. If this bit is set, the analog inputs are buffered, allowing the user to
place source impedances on the front end without contributing gain errors to the system. With the
buffer disabled, the voltage on the analog input pins can be from 50 mV below AGND to 50 mV above
AVDD. When the buffer is enabled, it requires some headroom; therefore, the voltage on any input pin
must be limited to 250 mV within the power supply rails.
CON3
U/B
Polarity select bit. When this bit is set, unipolar operation is selected. When this bit is cleared, bipolar
operation is selected.
CON2 to CON0
G2 to G0
Gain select bits. These bits are written by the user to select the ADC input range as follows:
G2
G1
G0
Gain
ADC Input Range (5 V Reference)
0
1
±5 V
0
1
Reserved
0
1
0
Reserved
0
1
8
±625 mV
1
0
16
±312.5 mV
1
0
1
32
±156.2 mV
1
0
64
±78.125 mV
1
128
±39.06 mV
相關PDF資料 |
PDF描述 |
|---|---|
| LQH3NPN220MJ0L | INDUCTOR POWER 22UH 510MA 1212 |
| PCMC063T-R68MN | COIL .68UH POWER CHOKE 20% SMD |
| EVAL-AD7190EBZ | BOARD EVAL FOR AD7190 |
| EBM25DRSN | CONN EDGECARD 50POS DIP .156 SLD |
| PCMC063T-R22MN | COIL .22UH POWER CHOKE 20% SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7192EBZ | 制造商:Analog Devices 功能描述:EVAL BOARD, AD7192 24BIT ADC |
| EVAL-AD7193EBZ | 功能描述:EVAL BOARD FOR AD7193 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7194EBZ | 功能描述:EVAL BOARD FOR AD7194 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7195EBZ | 功能描述:BOARD EVAL FOR AD7195 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7262EDZ | 功能描述:BOARD EVAL CONTROL AD7262 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。