- 您現在的位置：買賣IC網 > PDF目錄17057 > EVAL-AD7193EBZ (Analog Devices Inc)EVAL BOARD FOR AD7193 PDF資料下載
參數資料
| 型號： | EVAL-AD7193EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR AD7193 |
| 設計資源： | EVAL-AD7193 Schematic AD7193 Gerber Files |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7193 |
| 已供物品： | 板，線纜 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
AD7193
Data Sheet
Rev. D | Page 22 of 56
COMMUNICATIONS REGISTER
RS2, RS1, RS0 = 000
The communications register is an 8-bit write-only register. All
communications to the part must start with a write operation to
the communications register. The data written to the communi-
cations register determine whether the next operation is a read
or write operation and in which register this operation occurs. For
read or write operations, when the subsequent read or write oper-
ation to the selected register is complete, the interface returns to
where it expects a write operation to the communications register.
This is the default state of the interface and, on power-up or after
a reset, the ADC is in this default state waiting for a write
operation to the communications register. In situations where the
interface sequence is lost, a write operation of at least 40 serial
clock cycles with DIN high returns the ADC to this default state
by resetting the entire part. Table 17 outlines the bit designations
for the communications register. CR0 through CR7 indicate the
bit location, CR denoting that the bits are in the communications
register. CR7 denotes the first bit of the data stream. The number
in parentheses indicates the power-on/reset default status of
that bit.
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
WEN(0)
R/W(0)
RS2(0)
RS1(0)
RS0(0)
CREAD(0)
0(0)
Table 17. Communications Register (CR) Bit Designations
Bit Location
Bit Name
Description
CR7
WEN
Write enable bit. For a write to the communications register to occur, 0 must be written to this bit. If a 1 is
the first bit written, the part does not clock onto subsequent bits in the register; rather, it stays at this bit
location until a 0 is written to this bit. After a 0 is written to the WEN bit, the next seven bits are loaded to
the communications register. Idling the DIN pin high between data transfers minimizes the effects of
spurious SCLK pulses on the serial interface.
CR6
R/W
0 in this bit location indicates that the next operation is a write to a specified register.
1 in this bit position indicates that the next operation is a read from the designated register.
CR5 to CR3
RS2 to RS0
Register address bits. These address bits are used to select which registers of the ADC are selected during
the serial interface communication (see Table 18).
CR2
CREAD
Continuous read of the data register. When this bit is set to 1 (and the data register is selected), the serial
interface is configured so that the data register can be continuously read; that is, the contents of the data
register are automatically placed on the DOUT pin when the SCLK pulses are applied after the RDY pin
goes low to indicate that a conversion is complete. The communications register does not have to be
written to for subsequent data reads. To enable continuous read, Instruction 01011100 must be written to the
communications register. To disable continuous read, Instruction 01011000 must be written to the communica-
tions register while the RDY pin is low. While continuous read is enabled, the ADC monitors activity on the
DIN line so that it can receive the instruction to disable continuous read. Additionally, a reset occurs if
40 consecutive 1s occur on DIN; therefore, hold DIN low until an instruction is written to the device.
CR1 to CR0
0
These bits must be programmed to Logic 0 for correct operation.
Table 18. Register Selection
RS2
RS1
RS0
Register
Register Size
0
Communications register during a write operation
8 bits
0
Status register during a read operation
8 bits
0
1
Mode register
24 bits
0
1
0
Configuration register
24 bits
0
1
Data register/data register plus status information
24 bits/32 bits
1
0
ID register
8 bits
1
0
1
GPOCON register
8 bits
1
0
Offset register
24 bits
1
Full-scale register
24 bits
相關PDF資料 |
PDF描述 |
|---|---|
| TRK-MPC5634M | TRAK 5634M 144PN R2.1 |
| REF191GSZ | IC VREF SERIES PREC 2.048V 8SOIC |
| DEMO56F8014-EE | BOARD DEMO FOR 56F8014 |
| 0210490222 | CABLE JUMPER 1.25MM .152M 16POS |
| EVAL-AD7795EBZ | BOARD EVAL FOR AD7795 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7194EBZ | 功能描述:EVAL BOARD FOR AD7194 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7195EBZ | 功能描述:BOARD EVAL FOR AD7195 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7262EDZ | 功能描述:BOARD EVAL CONTROL AD7262 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7264EDZ | 功能描述:BOARD EVALUATION FOR AD7264 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7265CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
發布緊急采購，3分鐘左右您將得到回復。