參數資料
型號： EVAL-AD7682EDZ
廠商： Analog Devices Inc
文件頁數： 21/32頁
文件大小： 0K
描述： BOARD EVAL AD7682
標準包裝： 1
系列： PulSAR®
ADC 的數量： 1
位數： 16
采樣率（每秒）： 250k
數據接口： 串行
輸入范圍： ±VREF
在以下條件下的電源（標準）： 12.5mW @ 250kSPS，5V
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7682
已供物品： 板
AD7682/AD7689
Data Sheet
Rev. D | Page 28 of 32
CHANNEL SEQUENCER
The AD7682/AD7689 include a channel sequencer useful for
scanning channels in a repeated fashion. Channels are scanned
as singles or pairs, with or without the temperature sensor, after
the last channel is sequenced.
The sequencer starts with IN0 and finishes with IN[7:0] set in
CFG[9:7]. For paired channels, the channels are paired depend-
ing on the last channel set in CFG[9:7]. Note that in sequencer
mode, the channels are always paired with the positive input on
the even channels (IN0, IN2, IN4, IN6), and with the negative
input on the odd channels (IN1, IN3, IN5, IN7). For example,
setting CFG[9:7] = 110 or 111 scans all pairs with the positive
inputs dedicated to IN0, IN2, IN4, and IN6.
CFG[2:1] are used to enable the sequencer. After the CFG
register is updated, DIN must be held low while reading data
out for Bit 13, or the CFG register begins updating again.
Note that while operating in a sequence, some bits of the CFG
register can be changed. However, if changing CFG[11] (paired
or single channel) or CFG[9:7] (last channel in sequence), the
sequence reinitializes and converts IN0 (or IN0/IN1 pairs) after
the CFG register is updated.
Figure 39 details the timing for all three modes without a busy
indicator. Refer to the Read/Write Spanning Conversion
Conversion Without a Busy Indicator section for more details.
The sequencer can also be used with the busy indicator and
details for these timings can be found in the General Timing
For sequencer operation, the CFG register should be set during
the (n 1) phase after power-up. On phase (n), the sequencer
setting takes place and acquires IN0. The first valid conversion
result is available at phase (n + 1). After the last channel set in
CFG[9:7] is converted, the internal temperature sensor data is
output (if enabled), followed by acquisition of IN0.
Examples
With all channels configured for unipolar mode to GND,
including the internal temperature sensor, the sequence scans in
the following order:
IN0, IN1, IN2, IN3, IN4, IN5, IN6, IN7, TEMP, IN0, IN1, IN2, …
For paired channels with the internal temperature sensor
enabled, the sequencer scans in the following order:
IN0, IN2, IN4, IN6, TEMP, IN0, …
Note that IN1, IN3, IN5, and IN7 are referenced to a GND
sense or VREF/2, as detailed in the Input Configurations section.
ACQUISITION
(n – 1) UNDEFINED
ACQUISITION
(n), IN0
ACQUISITION
(n + 1), IN1
ACQUISITION
(n + 2), IN2
PHASE
POWER
UP
EOC
SOC
EOC
CONVERSION
(n – 1) UNDEFINED
CONVERSION
(n), IN0
CONVERSION
(n + 1), IN1
CONVERSION
(n – 2) UNDEFINED
07
35
3-
0
4
6
tCONV
tCYC
tDATA
CNV
DIN
SDO
XXX
MSB
XXX
MSB
XXX
NOTES
1. CNV MUST BE HIGH PRIOR TO THE END OF CONVERSION (EOC) TO AVOID THE BUSY INDICATOR.
2. A TOTAL OF 16 SCK FALLING EDGES ARE REQUIRED TO RETURN SDO TO HIGH-Z. IF CFG READBACK IS ENABLED,
A TOTAL OF 30 SCK FALLING EDGES IS REQUIRED TO RETURN SDO TO HIGH-Z.
DATA IN0
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 3)
XXX
MSB
IN0
MSB
IN1
DIN
SDO
DATA IN1
DATA IN0
DATA IN1
DIN
CFG (n)
SDO
SCK
1
NOTE 1
16
NOTE 2
2
1
SCK
116
16
nn
n
n + 1
n
1
SCK
1
116
16
1
CFG (n)
RDC
RAC
RSC
CFG (n)
Figure 39. General Channel Sequencer Timing Without a Busy Indicator
相關PDF資料
PDF描述
LGU2E331MELZ CAP ALUM 330UF 250V 20% SNAP
EVAL-AD7982SDZ BOARD EVAL FOR AD7982
VI-J1L-EY CONVERTER MOD DC/DC 28V 50W
VE-21L-EY CONVERTER MOD DC/DC 28V 50W
DC1009A-A BOARD DELTA SIGMA ADC LTC2492
相關代理商/技術參數
參數描述
EVAL-AD7683CB 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN
EVAL-AD7683CBZ 制造商:Analog Devices 功能描述:EVAL BOARD 18BIT 100ksps I.C.
EVAL-AD7683SDZ 功能描述:數據轉換 IC 開發工具 EVAL BOARD 18BIT 100ksps I.C. RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7684CBZ 功能描述:BOARD EVALUATION FOR AD7684 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7685CB 制造商:Analog Devices 功能描述:Evaluation Board For Use With Either The Analog Devices 制造商:Analog Devices 功能描述:EVAL FOR AD7685 - Bulk 制造商:Rochester Electronics LLC 功能描述:EVAL FOR AD7685 - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*