- 您現在的位置：買賣IC網 > PDF目錄17036 > EVAL-AD7682EDZ (Analog Devices Inc)BOARD EVAL AD7682 PDF資料下載
參數資料
| 型號： | EVAL-AD7682EDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL AD7682 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 12.5mW @ 250kSPS，5V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7682 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7682/AD7689
Data Sheet
Rev. D | Page 30 of 32
READ/WRITE SPANNING CONVERSION WITH A
BUSY INDICATOR
any host using an SPI, serial port, or FPGA with an interrupt
input. The connection diagram is shown in Figure 42, and the
corresponding timing is given in Figure 43. For the SPI, the
host should use CPHA = CPOL = 1. Reading/writing spanning
conversion is shown, which covers all three modes detailed in
the Digital Interface section.
A rising edge on CNV initiates a conversion, ignores data
present on DIN and forces SDO to high impedance. After the
conversion is initiated, it continues until completion irrespec-
tive of the state of CNV. CNV must be returned low before the
safe data transfer time, tDATA, and then held low beyond the
conversion time, tCONV, to generate the busy signal indicator.
When the conversion is complete, SDO transitions from high
impedance to low (data ready), and with a pull-up to VIO, SDO
can be used to interrupt the host to begin data transfer.
the acquisition phase and power-down. The host must enable
the MSB of the CFG register at this time (if necessary) to begin
the CFG update. While CNV is low, both a CFG update and a
data readback take place. The first 14 SCK rising edges are used to
update the CFG register, and the first 16 SCK falling edges clock
out the conversion results starting with the MSB. The restric-
tion for both configuring and reading is that they both occur
before the tDATA time elapses for the next conversion. All 14 bits of
CFG[13:0] must be written or they are ignored. Also, if the 16-bit
conversion result is not read back before tDATA elapses, it is lost.
The SDO data is valid on both SCK edges. Although the rising
edge can be used to capture the data, a digital host using the
SCK falling edge allows a faster reading rate, provided it has an
acceptable hold time. After the optional 17th (or 31st) SCK
falling edge, SDO returns to high impedance. Note that if the
optional SCK falling edge is not used, the busy feature cannot
be detected, as described in the General Timing with a Busy
Indicator section.
If CFG readback is enabled, the CFG register associated with
the conversion result is read back MSB first following the LSB of
the conversion result. A total of 31 SCK falling edges is required
to return SDO to high impedance if this is enabled.
AD7682/
AD7689
MISO
MOSI
SCK
SS
SDO
VIO
FOR SPI USE CPHA = 1, CPOL = 1.
SCK
CNV
DIN
DIGITAL HOST
IRQ
07
35
3-
03
8
SCK
ACQUISITION (n)
ACQUISITION
(n + 1)
CNV
DIN
SDO
MSB
– 1
1
2
BEGIN DATA (n – 1)
BEIGN CFG (n + 1)
CFG
MSB
LSB
+ 1
LSB
15
SEE NOTE
NOTES:
1. THE LSB IS FOR CONVERSION RESULTS OR THE CONFIGURATION REGISTER CFG (n – 1) IF
16 SCK FALLING EDGES = LSB OF CONVERSION RESULTS.
30 SCK FALLING EDGES = LSB OF CONFIGURATION REGISTER.
ON THE 17TH OR 31st SCK FALLING EDGE, SDO IS DRIVEN TO HIGH IMPENDANCE.
OTHERWISE, THE LSB REMAINS ACTIVE UNTIL THE BUSY INDICATOR IS DRIVEN LOW.
16
17/
31
17/
31
CONVERSION (n)
CONVERSION
(n – 1)
(QUIET
TIME)
END DATA (n – 2)
END DATA (n – 1)
END CFG (n + 1)
END CFG (n)
X
XX
X
tDATA
UPDATE (n + 1)
CFG/SDO
LSB
+ 1
LSB
CONVERSION (n – 1)
(QUIET
TIME)
UPDATE (n)
CFG/SDO
tCYC
tACQ
tHDIN
tHSDO
tDSDO
tSDIN
tDATA
tCONV
tCNVH
tDIS
tEN
CFG
MSB –1
07
35
3-
03
9
tSCK
tSCKH
tSCKL
相關PDF資料 |
PDF描述 |
|---|---|
| LGU2E331MELZ | CAP ALUM 330UF 250V 20% SNAP |
| EVAL-AD7982SDZ | BOARD EVAL FOR AD7982 |
| VI-J1L-EY | CONVERTER MOD DC/DC 28V 50W |
| VE-21L-EY | CONVERTER MOD DC/DC 28V 50W |
| DC1009A-A | BOARD DELTA SIGMA ADC LTC2492 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7683CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| EVAL-AD7683CBZ | 制造商:Analog Devices 功能描述:EVAL BOARD 18BIT 100ksps I.C. |
| EVAL-AD7683SDZ | 功能描述:數據轉換 IC 開發工具 EVAL BOARD 18BIT 100ksps I.C. RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-AD7684CBZ | 功能描述:BOARD EVALUATION FOR AD7684 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7685CB | 制造商:Analog Devices 功能描述:Evaluation Board For Use With Either The Analog Devices 制造商:Analog Devices 功能描述:EVAL FOR AD7685 - Bulk 制造商:Rochester Electronics LLC 功能描述:EVAL FOR AD7685 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。