- 您現在的位置：買賣IC網 > PDF目錄17061 > EVAL-AD7734EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7734 PDF資料下載
參數資料
| 型號： | EVAL-AD7734EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/32頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7734 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.4k |
| 數據接口： | 串行 |
| 輸入范圍： | ±10 V |
| 在以下條件下的電源（標準）： | 85mW @ 5V |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7734 |
| 已供物品： | 板，纜線，CD |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
| 相關產品： | AD7734BRUZ-REEL7TR-ND - IC ADC 24BIT 4CH SIG-DEL 28TSSOP AD7734BRUZ-REEL-ND - IC ADC 24BIT 4CH SIG-DEL 28TSSOP AD7734BRUZ-ND - IC ADC 24BIT 4-CH 28-TSSOP AD7734BRU-ND - IC ADC 24BIT 4-CH 28-TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7734
Data Sheet
Rev. A | Page 18 of 32
CHANNEL ZERO-SCALE CALIBRATION REGISTERS
24 Bits, Read/Write Registers, Address 10h–13h, Default Value
800000h
These registers hold the particular channel zero-scale
calibration coefficients. The value in these registers is used in
conjunction with the value in the corresponding channel full-
scale calibration register, the ADC zero-scale calibration
register, and the ADC full-scale register to digitally scale the
particular channel conversion results. The value in this register
is updated automatically following the execution of a channel
zero-scale system calibration.
The format of the channel zero-scale calibration register is a
sign bit and 22 bits unsigned value. Writing this register is
possible in the idle mode only (see the Calibration section for
more details).
CHANNEL FULL-SCALE CALIBRATION REGISTERS
24 Bits, Read/Write Registers, Address 18h–1Bh, Default Value
200000h
These registers hold the particular channel full-scale calibration
coefficients. The value in these registers is used in conjunction
with the value in the corresponding channel zero-scale
calibration register, the ADC zero-scale calibration register, and
the ADC full-scale register to digitally scale the particular
channel conversion results. The value in this register is updated
automatically following the execution of a channel full-scale
system calibration. Writing this register is possible in the idle
mode only (see the Calibration section for more details).
CHANNEL STATUS REGISTERS
8 Bits, Read-Only Register, Address 20h–23h, Default Value 20h × Channel Number
These registers contain individual channel status information and some general AD7734 status information. Reading the status registers
can be associated with reading the data registers in the dump mode. Reading the status registers is always associated with reading the data
registers in the continuous read mode (see the Digital Interface Description section for more details).
Bit
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mnemonic
0
CH1
CH0
0/P0
RDY/P1
NOREF
SIGN
OVR
Default
Channel Number
0
Bit
Mnemonic
Description
7–5
CH1–CH0
These bits reflect the channel number. This can be used for current channel identification and easier operation
of the dump mode and continuous read mode.
4
0/P0
When the status option bit of the corresponding channel setup register is reset to 0, this bit is read as a zero.
When the status option bit is set to 1, this bit reflects the state of the P0 pin, whether it is configured as an
input or an output.
3
RDY/P1
When the status option bit of the corresponding channel setup register is reset to 0, this bit reflects the
selected channel RDY bit in the ADC status register. When the status option bit is set to 1, this bit reflects the
state of the P1 pin, whether it is configured as an input or an output.
2
NOREF
This bit indicates the reference input status. If the voltage between the REFIN(+) and REFIN(–) pins is less than
NOREF, the trigger voltage and a conversion is executed, then the NOREF bit goes to 1.
1
SIGN
The voltage polarity at the analog input. It will be 0 for a positive voltage and 1 for a negative voltage.
0
OVR
This bit reflects either the overrange or the underrange on the analog input. The bit is set to 1 when the
analog input voltage goes over or under the nominal voltage range (see the Analog Input’s Extended Voltage
Range section).
相關PDF資料 |
PDF描述 |
|---|---|
| SK471M100ST | CAP ALUM 470UF 100V 20% RADIAL |
| 0982660774 | CBL 9POS 0.5MM JMPR TYPE D 5" |
| EVAL-AD7794EBZ | BOARD EVALUATION FOR AD7794 |
| VE-B2L-EY | CONVERTER MOD DC/DC 28V 50W |
| DC979A | BOARD DELTA SIGMA ADC LTC2442 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7738EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD7738 ADC 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7738EBZ | 功能描述:BOARD EVAL FOR AD7738 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7739EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7739EBZ | 功能描述:BOARD EVAL FOR AD7739 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7741/42EB | 制造商:Analog Devices 功能描述:Evaluation Board For Single And Multi-Channel Synchronous Voltage-To-Frequency Converters 制造商:Analog Devices 功能描述:EVALUATION BOARD IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。