參數資料
型號: EVAL-AD7942SDZ
廠商: Analog Devices Inc
文件頁數: 10/24頁
文件大小: 0K
描述: BOARD EVAL FOR AD7942
標準包裝: 1
系列: PulSAR®
ADC 的數量: 1
位數: 14
采樣率(每秒): 250k
數據接口: 串行
輸入范圍: 0 ~ 5.5 V
工作溫度: -40°C ~ 85°C
已用 IC / 零件: AD7942
已供物品:
AD7942
Rev. B | Page 18 of
24
CS Mode 3-Wire with Busy Indicator
This mode is most often used when a single AD7942 is
connected to an SPI-compatible digital host with an interrupt
input. The connection diagram is shown in Figure 32 and the
corresponding timing diagram is shown in Figure 33.
With SDI tied to VIO, a rising edge on CNV initiates a conver-
sion, selects the CS mode, and forces SDO to high impedance.
SDO is maintained in high impedance until the completion of
the conversion irrespective of the state of CNV. Prior to the
minimum conversion time, CNV can be used to select other
SPI devices, such as analog multiplexers. However, CNV must
be returned low before the minimum conversion time and held
low until the maximum conversion time to guarantee the
generation of the busy signal indicator. When the conversion
is complete, SDO goes from high impedance to low impedance.
With a pull-up on the SDO line, this transition can be used as
an interrupt signal to initiate the data reading controlled by the
digital host. The AD7942 then enters the acquisition phase and
powers down. The data bits are then clocked out, MSB first, by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host also using the SCK falling edge allows a faster
reading rate provided it has an acceptable hold time. After
the optional 15th SCK falling edge or when CNV goes high,
whichever is earlier, SDO returns to high impedance.
CNV
SCK
SDO
SDI
DATA IN
IRQ
CLK
CONVERT
VIO
DIGITAL HOST
AD7942
04
65
7-
0
32
47k
Figure 32. CS Mode 3-Wire with Busy Indicator
Connection Diagram (SDI High)
SDO
D13
D12
D1
D0
tDIS
SCK
12
3
13
14
15
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
tCNVH
tACQ
ACQUISITION
SDI = 1
04
65
7-
0
3
Figure 33. CS Mode 3-Wire with Busy Indicator, Serial Interface Timing (SDI High)
相關PDF資料
PDF描述
EVAL-AD7699EDZ BOARD EVALUATION FOR AD7699
EVAL-AD7689EDZ BOARD EVAL AD7689
VE-J1J-EY CONVERTER MOD DC/DC 36V 50W
EVAL-AD7682EDZ BOARD EVAL AD7682
LGU2E331MELZ CAP ALUM 330UF 250V 20% SNAP
相關代理商/技術參數
參數描述
EVAL-AD7944EBZ 功能描述:BOARD EVAL FOR AD7944 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7946CBZ 功能描述:BOARD EVALUATION FOR AD7946 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7946SDZ 功能描述:BOARD EVAL FOR AD7946 RoHS:否 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7949CBZ 制造商:Analog Devices 功能描述:EVAL BOARD 8 CH 250KSPS 14BIT ADC IC. - Bulk
EVAL-AD7949EDZ 功能描述:BOARD EVAL AD7949 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件