- 您現在的位置：買賣IC網 > PDF目錄16440 > EVAL-AD9393-ABZ (Analog Devices Inc)EVAL BOARD AD9393 PDF資料下載
參數資料
| 型號： | EVAL-AD9393-ABZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD AD9393 |
| 標準包裝： | 1 |
| 主要目的： | 視頻，開關，HDMI |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9393 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD9393
Rev. 0 | Page 23 of 40
0x25—Bit[1], Primary Output Enable
This bit places the primary output in active or high impedance
mode. The primary output is designated when using either 4:2:2
or DDR 4:4:4. In these modes, the data on the red and green
output channels (D[23:8]) is the primary output, whereas the
output data on the blue channel (D[7:0], DDR YCrCb) is the
secondary output. Double data rate 0 = primary output is in
high impedance mode. 1 = primary output is enabled. The
power-up default setting is 1.
0x25—Bit[0], Secondary Output Enable
This bit places the secondary output in active or high impe-
dance mode. The secondary output is designated when using
either 4:2:2 or DDR 4:4:4. In these modes, the data on the blue
output channel (D[7:0]) is the secondary output and the output
data on the red and green channels (D[23:8]) is the primary
output. Secondary output is always a DDR YCrCb data mode.
0 = secondary output is in high impedance mode. 1 = second-
ary output is enabled. The power-up default setting is 0.
0x26—Bit[7], Output Three-State
When enabled, this bit puts all outputs in a high impedance
state. 0 = normal outputs. 1 = all outputs in high impedance
mode. The power-up default setting is 0.
0x26—Bit[5], S/PDIF Three-State
When enabled, this bit places the S/PDIF audio output pins in a
high impedance state. 0 = normal S/PDIF output. 1 = S/PDIF
pins in high impedance mode. The power-up default setting is 0.
0x26—Bit[4], I2S Three-State
When enabled, this bit places the I2S output pins in a high
impedance state. 0 = normal I2S output. 1 = I2S pins are in
high impedance mode. The power-up default setting is 0.
0x26—Bit[3], Power-Down Ball Polarity
This bit defines the polarity of the input power-down ball.
0 = power-down ball is active low. 1 = power-down ball is
active high. The power-up default setting is 1.
0x26—Bits[2:1], Power-Down Ball Function
These bits define the different operational modes of the power-
down ball. These bits are functional only when the power-down
ball is active; when it is inactive, the part is powered up and
functioning. 0x = the chip is powered down and all outputs are
in high impedance mode. 1x = the chip remains powered up,
but all outputs are in three-state outputs mode. The power-up
default setting is 00.
0x26—Bit[0], Power-Down
This bit is used to put the chip in power-down mode. In this
mode, the power dissipation is reduced to a fraction of the
typical power (see Table 2 for exact power dissipation). When
in power-down, the HSOUT, VSOUT, DCLK, and all 24 of the
data outputs are put into a high impedance state. Circuit blocks
that continue to be active during power-down include the
voltage references, sync detection, and the serial register. These
blocks facilitate a fast start up from power-down. 0 = normal
operation. 1 = power-down. The power-up default setting is 0.
0x27—Bit[7], Auto Power-Down Enable
This bit enables the chip to go into low power mode, or seek
mode if no sync inputs are detected. 0 = auto power-down
disabled. 1 = chip powers down if no sync inputs are present.
The power-up default setting is 1.
0x27—Bit[6], HDCP A0
This bit sets the LSB of the address of the HDCP I2C. Set this bit
to 1 only for a second receiver in a dual-link configuration. The
power-up default is 0.
0x27—Bit[5], Clock Test
The power-up default setting is 0.
相關PDF資料 |
PDF描述 |
|---|---|
| H1BXH-6436G | IDC CABLE - HSR64H/AE64G/X |
| EVAL-ADV7511W-ABZ | BOARD EVAL FOR ADV7511W-ABZ |
| EVAL-ADV7541-CBZ | BOARD EVALUATION FOR ADV7541 |
| VI-J1M-EX | CONVERTER MINIMOD DC/DC 10V 75W |
| EVAL-ADV7523A-CBZ | BOARD EVALUATION FOR ADV7523 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD9393-AKZ | 功能描述:EVAL KIT 9393 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| EVAL-AD974CB | 功能描述:BOARD EVAL FOR AD974 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD976ACB | 功能描述:BOARD EVAL FOR AD976A RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD976CB | 功能描述:BOARD EVAL FOR AD976 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD977ACB | 功能描述:BOARD EVAL FOR AD977A RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。