- 您現在的位置：買賣IC網 > PDF目錄358706 > F25L016A (Elite Semiconductor Memory Technology Inc.) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | F25L016A |
| 廠商： | Elite Semiconductor Memory Technology Inc. |
| 元件分類： | FLASH |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 14/31頁 |
| 文件大?。?/td> | 384K |
| 代理商： | F25L016A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
ES MT
Auto Address Increment (AAI) WORD Program
The AAI program instruction allows multiple bytes of data to be programmed without re-issuing the next sequential address location.
This feature decreases total programming time when the multiple bytes or entire memory array is to be programmed. An AAI program
instruction pointing to a protected memory area will be ignored. The selected address range must be in the erased state (FFH) when
initiating an AAI program instruction. While within AAI WORD programming sequence, the only valid instructions are AAI WORD
program operation, RDSR, WRDI. Users have three options to determine the completion of each AAI WORD program cycle: hardware
detection by reading the SO; software detection by polling the BUSY in the software status register or wait T
BP
. Refer to End-of-Write
Detection section for details.
Prior to any write operation, the Write-Enable (WREN) instruction must be executed. The AAI WORD program instruction is initiated by
executing an 8-bit command, ADH, followed by address bits [A
23
-A
0
]. Following the addresses, two bytes of data is input sequentially.
The data is input sequentially from MSB (bit 7) to LSB (bit 0). The first byte of data(DO) will be programmed into the initial address
[A
23
-A
1
] with A
0
=0; The second byte of data(D1) will be programmed into the initial address [A
23
-A
1
] with A
0
=1.CE must be driven
high before the AAI WORD program instruction is executed. The user must check the BUSY status before entering the next valid
command. Once the device indicates it is no longer busy, data for next two sequential addresses may be programmed and so on. When
the last desired byte had been entered, check the busy status using the hardware method or the RDSR instruction and execute the
WRDI instruction, to terminate AAI. User must check busy status after WRDI to determine if the device is ready for any command.
Please refer to Figures 7 and Figures 8.
There is no wrap mode during AAI programming; once the highest unprotected memory address is reached, the device will exit AAI
operation and reset the Write-Enable-Latch bit (WEL = 0) and the AAI bit (AAI=0).
End of Write Detection
There are three methods to determine completion of a program cycle during AAI WORD programming: hardware detection by reading
the SO, software detection by polling the BUSY bit in the Software Status Register or wait T
BP.
The hardware end of write detection
method is described in the section below.
Hardware End of Write Detection
The hardware end of write detection method eliminates the overhead of polling the BUSY bit in the software status register during an AAI
Word PROGRAM OPERATION. The 8bit command, 70H, configures the SO to indicate Flash Busy status during AAI WORD
programming (refer to figure5). The 8bit command, 70H, must be executed prior to executing an AAI WORD program instruction. Once
an internal programming operation begins, assertingCE will immediately drive the status of the internal flash status on the SO pin. A “0”
F25L016A
Elite Semiconductor Memory Technology Inc.
Revision
:
1.2
14/31
Publication Date
:
Mar. 2007
Indicates the device is busy ; a “1” Indicates the device is ready for the next instruction. De-assertingCE will return the SO pin to
tri-state. The 8bit command, 80H,disables the SO pin to output busy status during AAI WORD program operation and return SO pin to
output software register data during AAI WORD programming (refer to figure6).
FIGURE 5 : ENABLE SO AS HARDWARE
DURING AAI PROGRAMMING
BY
/
RY
FIGURE 6 : DISABLE SO AS HARDWARE
DURING AAI PROGRAMMING
BY
/
RY
相關PDF資料 |
PDF描述 |
|---|---|
| F49B002UA | 2 Mbit (256K x 8) 5V Only CMOS Flash Memory |
| F49L004BA | 4 Mbit (512K x 8) 3V Only CMOS Flash Memory |
| FLH0041G | 0.2 Amp Linear Power Operational Amplifier in a Hermetic 12-lead Package |
| FLM3439-12F | C-Band Internally Matched FET |
| FLM5359-12F | C-Band Internally Matched FET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| F25L016A_08 | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16Mbit (2Mx8) 3V Only Serial Flash Memory |
| F25L016A_1 | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16Mbit (2Mx8) 3V Only Serial Flash Memory |
| F25L016A-100PAG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16Mbit (2Mx8) 3V Only Serial Flash Memory |
| F25L016A-100PAIG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16Mbit (2Mx8) 3V Only Serial Flash Memory |
| F25L016A-50PAG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16Mbit (2Mx8) 3V Only Serial Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。