參數資料
型號： FM3808-70-T
廠商： Electronic Theatre Controls, Inc.
元件分類： DRAM
英文描述： 4Kb FRAM Serial 3V Memory
中文描述： 4Kb的鐵電串行3V的記憶
文件頁數： 13/28頁
文件大小： 191K
代理商： FM3808-70-T
FM3808
Rev 1.1
May 2003
Page 13 of 28
Interrupts
The supervisor was designed to serve diverse
applications. Its sophistication and programmability
make the supervisor function highly configurable for
the host system. The interrupt block is capable of
providing system interrupt or reset conditions, and
can even power up a system at a preprogrammed
time. Although the INT pin is described as an
interrupt, the pin may be used as a reset source as
well.
The supervisor provides three potential interrupt
sources. They include the watchdog timer, the power
monitor, and the clock/calendar alarm. Each can be
individually enabled and assigned to drive the INT
pin. In addition, each has an associated flag bit that
the host processor can use to determine the cause of
the interrupt.
Some of the sources have additional control bits that
determine functional behavior. In addition, the pin
driver has three bits that specify its behavior when an
interrupt occurs. A functional diagram of the interrupt
logic is shown below.
The three interrupts each have a source and an
enable. Both the source and the enable must be active
(true high) in order to generate an interrupt output.
Only one source is necessary to drive the pin. The
user can identify the source by reading the
Flags/Control register, which contains the flags
associated with each source. All flags are cleared to 0
when the register is read. The cycle must be a
complete read cycle (/WE high), otherwise the flags
will not be cleared. The power monitor has two
programmable settings that are explained above in the
power monitor section.
Once an interrupt source is active, the pin driver
determines the behavior of the output. It has two
programmable settings as shown below. Pin driver
control bits are located in the Interrupts register
7FF6h bits D3-D2.
Watchdog
Timer
WDF
WIE
Power
Monitor
PF
PFE
VINT
Clock
Alarm
AF
AIE
Pin
Driver
ABE
P/L
H/L
VDD
INT
Figure 5. Interrupt Block Diagram
According to the programming selections, the pin can
be driven in the backup mode for an alarm interrupt.
In addition, the pin can be an active low (open-drain)
or active high (push-pull) driver. If programmed for
operation during backup mode, it can only be active
low. Lastly, the pin can provide a one-shot function
so that the active condition is a pulse, or a level
condition. In One-Shot mode, the pulse width is
internally fixed at approximately 200 ms. This mode
is intended to reset a host microcontroller. In Level
mode, the pin goes to its active polarity until the
Flags/Control register is read by the user. This mode
is intended to be used as an interrupt to a host
microcontroller. The control bits are summarized as
follows.
Watchdog Interrupt Enable - WIE. When set to 1, the
watchdog timer drives the INT pin as well as an
internal flag when a watchdog timeout occurs. When
相關PDF資料
PDF描述
FM3808DK 4Kb FRAM Serial 3V Memory
FMA10A General Purpose(Dual Digital Transistor)(通用(雙數字晶體管))
FMA11A Emitter Common (Dual Digital Transistors)(公共發射級(雙數字晶體管))
FMA1 General purpose (dual digital transistors)
FMA1A General purpose (dual digital transistors)
相關代理商/技術參數
參數描述
FM3808DK 制造商:RAMTRON 制造商全稱:RAMTRON 功能描述:256Kb Bytewide FRAM w/ Real-Time Clock
FM3808-S 制造商:Ramtron International Corporation 功能描述:FRAM RTC 256K SMD 3808 TSOP32
FM3808-SG 制造商:Ramtron International Corporation 功能描述:FRAM RTC 256K SMD 3808 TSOP32
FM380-A 制造商:FORMOSA 制造商全稱:Formosa MS 功能描述:Silicon epitaxial planer type
FM380-AL 制造商:FORMOSA 制造商全稱:Formosa MS 功能描述:Chip Schottky Barrier Diodes - Silicon epitaxial planer type
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*