- 您現在的位置：買賣IC網 > PDF目錄296087 > HB288032MM1 FLASH 2.7V PROM CARD, XMA7 PDF資料下載
參數資料
| 型號： | HB288032MM1 |
| 元件分類： | PROM |
| 英文描述： | FLASH 2.7V PROM CARD, XMA7 |
| 封裝： | CARD-7 |
| 文件頁數： | 48/80頁 |
| 文件大?。?/td> | 236K |
| 代理商： | HB288032MM1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
HB288032MM1
52
Data in
Data out
command
response
data error
command
from
host
to card
from
card
to host
data error token
from card to host
Next
commnand
Read Operation-Data Error
Data Write Overview
As for the read operation, while in SPI mode the MultiMediaCard supports single block write commands
only. Upon reception of a valid write command (CMD24 in the MultiMediaCard protocol), the card will
respond with a response token and will wait for a data block to be sent from the host. CRC suffix, block
length and start address restrictions are (with the exception of the CSD parameter WRITE_BL_PARTIAL
controlling the partial block write option) identical to the read operation (refer to Figure “Write
Operation”).
Data in
Data out
command
data block
response
data_response busy
command
from
host
to card
data from
host
to card
from
card
to host
data
response and
busy from
card
new command
from host
Write Operation
After a data block has been received, the card will respond with a data-response token. If the data block
has been received without errors, it will be programmed. As long as the card is busy programming, a
continuous stream of busy tokens will be sent to the host (effectively holding the DataOut line low). Once
the programming operation is completed, the host must check the results of the programming using the
SEND_STATUS command (CMD13). Some errors (e.g. address out of range, write protect violation etc.)
are detected during programming only. The only validation check performed on the data block and
communicated to the host via the data-response token is the CRC. While the card is busy, resetting the CS
signal will not terminate the programming process. The card will release the DataOut line (tri-state) and
continue with programming. If the card is reselected before the programming is finished, the DataOut line
will be forced back to low and all commands will be rejected. Resetting a card (using CMD0) will
terminate any pending or active programming operation. This may destroy the data formats on the card. It
is in the responsibility of the host to prevent it.
相關PDF資料 |
PDF描述 |
|---|---|
| HB28A896IA1 | 448M X 16 FLASH 5V PROM CARD, XMA68 |
| HB56A232BW-6C | 2M X 32 FAST PAGE DRAM MODULE, 60 ns, SMA72 |
| HB56U432SB-5N | 4M X 32 EDO DRAM MODULE, 50 ns, SMA72 |
| HBCC-471J-02 | 1 ELEMENT, 470 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
| HBCC-1R2K-02 | 1 ELEMENT, 1.2 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB288064A5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288064A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288064C5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288064C6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288064MM1 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:MultiMediaCard 64 MByte |
發布緊急采購，3分鐘左右您將得到回復。