- 您現在的位置：買賣IC網 > PDF目錄353252 > HC4052 (NXP Semiconductors N.V.) T-PNP SI-AF PO PDF資料下載
參數資料
| 型號： | HC4052 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | T-PNP SI-AF PO |
| 中文描述： | 雙4通道模擬多路復用器/解復用器 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 341K |
| 代理商： | HC4052 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MC74VHC4051, MC74VHC4052, MC74VHC4053
http://onsemi.com
11
RL
Figure 11. Crosstalk Between Any Two
Switches, Test Set–Up
Figure 12. Power Dissipation Capacitance,
Test Set–Up
Figure 14a. Total Harmonic Distortion, Test Set–Up
Figure 13b. Plot, Harmonic Distortion
0
–10
–20
–30
–40
–50
– 100
1.0
2.0
3.125
FREQUENCY (kHz)
dB
–60
–70
–80
–90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
ON
6
7
8
16
VEE
CL*
*Includes all probe and jig capacitance
OFF
RL
VIS
RL
CL*
VOS
fin
0.1
F
ON/OFF
6
7
8
16
VCC
CHANNEL SELECT
NC
COMMON O/I
OFF/ON
ANALOG I/O
VCC
A
11
VCC
VEE
ON
6
7
8
16
VCC
VEE
0.1
F
CL*
fin
RL
TO
DISTORTION
METER
*Includes all probe and jig capacitance
VOS
VIS
APPLICATIONS INFORMATION
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this
example:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In this example,
the difference between VCC and VEE is ten volts. Therefore,
using the configuration of Figure 15, a maximum analog
signal of ten volts peak–to–peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not
connected). However, tying unused analog inputs and
outputs to VCC or GND through a low value resistor helps
minimize crosstalk and feedthrough noise that may be
picked up by an unused switch.
Although used here, balanced supplies are not a
requirement. The only constraints on the power supplies are
that:
VCC – GND = 2 to 6 volts
VEE – GND = 0 to –6 volts
VCC – VEE = 2 to 12 volts
and VEE ≤ GND
Whenvoltage transients above VCCand/orbelowVEEare
anticipated on the analog channels, external Germanium or
Schottky diodes (Dx) are recommended as shown in Figure
16. These diodes should be able to absorb the maximum
anticipated current surges during clipping.
相關PDF資料 |
PDF描述 |
|---|---|
| HDSP-7401-HCZ00 | 7.6 mm (0.3 inch) Micro Bright Seven Segment Displays |
| HDSP-315H-EE000 | NTE DIN Rail Mount Sockets, Socket Type: Miniature DPDT, Current Rating: 7 A, Voltage Rating: 300 V, Number of Pins: 8, Mounting Type: DIN Rail, Panel or Surface Mount, Features: Pressure clamp screws |
| HDSP-316H-EE000 | PC Board Relay Socket |
| HDSP-315H-EF000 | RELAY-4 PIN BLADE SOCKET |
| HDSP-316H-EF000 | 10 mm and 13 mm Slim Font Seven Segment Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC4052A-L85H WAF | 制造商:ON Semiconductor 功能描述: |
| HC4052BGHF30705 | 制造商:DENSITRON 功能描述: |
| HC4053 | 制造商:SLS 制造商全稱:System Logic Semiconductor 功能描述:Analog Multiplexer/Demultiplexer |
| HC4054 | 制造商:HUASHAN 制造商全稱:HUASHAN 功能描述:NPN SILICON TRANSISTOR |
| HC4056B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。