- 您現在的位置：買賣IC網 > PDF目錄299170 > HD6433837L 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | HD6433837L |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 80/194頁 |
| 文件大?。?/td> | 2303K |
| 代理商： | HD6433837L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
170
8272E–AVR–04/2013
ATmega164A/PA/324A/PA/644A/PA/1284/P
18.3
SS pin functionality
18.3.1
Slave mode
When the SPI is configured as a Slave, the Slave Select (SS) pin is always input. When SS is
held low, the SPI is activated, and MISO becomes an output if configured so by the user. All
other pins are inputs. When SS is driven high, all pins are inputs, and the SPI is passive, which
means that it will not receive incoming data. Note that the SPI logic will be reset once the SS pin
is driven high.
The SS pin is useful for packet/byte synchronization to keep the slave bit counter synchronous
with the master clock generator. When the SS pin is driven high, the SPI slave will immediately
reset the send and receive logic, and drop any partially received data in the Shift Register.
18.3.2
Master mode
When the SPI is configured as a Master (MSTR in SPCR is set), the user can determine the
direction of the SS pin.
If SS is configured as an output, the pin is a general output pin which does not affect the SPI
system. Typically, the pin will be driving the SS pin of the SPI Slave.
If SS is configured as an input, it must be held high to ensure Master SPI operation. If the SS pin
is driven low by peripheral circuitry when the SPI is configured as a Master with the SS pin
defined as an input, the SPI system interprets this as another master selecting the SPI as a
slave and starting to send data to it. To avoid bus contention, the SPI system takes the following
actions:
1.
The MSTR bit in SPCR is cleared and the SPI system becomes a Slave. As a result of
the SPI becoming a Slave, the MOSI and SCK pins become inputs.
2.
The SPIF Flag in SPSR is set, and if the SPI interrupt is enabled, and the I-bit in SREG is
set, the interrupt routine will be executed.
Thus, when interrupt-driven SPI transmission is used in Master mode, and there exists a possi-
bility that SS is driven low, the interrupt should always check that the MSTR bit is still set. If the
MSTR bit has been cleared by a slave select, it must be set by the user to re-enable SPI Master
mode.
18.4
Data modes
There are four combinations of SCK phase and polarity with respect to serial data, which are
determined by control bits CPHA and CPOL. The SPI data transfer formats are shown in Figure
18-3 on page 171 and Figure 18-4 on page 171. Data bits are shifted out and latched in on
opposite edges of the SCK signal, ensuring sufficient time for data signals to stabilize. This is
clearly seen by summarizing Table 18-3 on page 172 and Table 18-4 on page 172, as done in
相關PDF資料 |
PDF描述 |
|---|---|
| HD6433837SH | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP100 |
| HD64463 | MULTIFUNCTION PERIPHERAL, PBGA387 |
| HD6473258CP10 | 8-BIT, OTPROM, MICROCONTROLLER, PQCC68 |
| HD74AC174T | D FLIP-FLOP, PDSO16 |
| HD74HC149FP | HC/UH SERIES, 8-BIT ENCODER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD6433837S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:H8/3834 Series H8/3837 HD6433837.HD6433837S.HD64473837. H8/3836 HD6433836.HD6433836S H8/3835 HD6433835.HD6433835S H8/3834 HD6433834.HD633834S.HD6473834 H8/3833 HD6433833.HD6433833S H8/3832 HD6433832S Hardware Manual |
| HD6433837SD | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:single-chip microcomputers |
| HD6433837SE | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:single-chip microcomputers |
| HD6433837SF | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:single-chip microcomputers |
| HD6433837SH | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:single-chip microcomputers |
發布緊急采購，3分鐘左右您將得到回復。