- 您現在的位置：買賣IC網 > PDF目錄67681 > HMC714LP5E (HITTITE MICROWAVE CORP) 100 MHz - 5800 MHz RF/MICROWAVE LINEAR DETECTOR, 15 dBm INPUT POWER-MAX PDF資料下載
參數資料
| 型號： | HMC714LP5E |
| 廠商： | HITTITE MICROWAVE CORP |
| 元件分類： | 檢測器 |
| 英文描述： | 100 MHz - 5800 MHz RF/MICROWAVE LINEAR DETECTOR, 15 dBm INPUT POWER-MAX |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, SMT, 32 PIN |
| 文件頁數： | 32/40頁 |
| 文件大?。?/td> | 1985K |
| 代理商： | HMC714LP5E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
P
O
W
E
R
D
E
T
E
C
T
O
R
S
-
SM
T
12
12 - 163
Standby Mode
The ENX can be used to force the power detector into a low-power standby mode. In this mode, the entire power
detector is powered-down. As ENX is deactivated, power is restored to all of the circuits. There is no memory of
previous conditions. Coming-out of stand-by, CINT and COFS capacitors will require recharging, so if large capacitor
values have been chosen, the wake-up time will be lengthened.
DC Offset Compensation Loop
Internal DC offsets, which are input signal dependant, require continuous cancellation. Offset cancellation is a critical
function needed for maintenance of measurement accuracy and sensitivity. The DC offset cancellation loop performs
this function, and its response is largely defined by the capacitance off. Setting DC offset cancellation, loop bandwidth
strives to strike a balance between offset cancellation accuracy, and loop response time. A larger value of COFS results
in a more precise offset cancellation, but at the expense of a slower offset cancellation response. A smaller value of
COFS tilts the performance trade-off towards a faster offset cancellation response. The optimal loop bandwidth setting
will allow internal offsets to be cancelled at a minimally acceptable speed.
full description on crest factor optimization.
iPAR Reference Outputs: IREFA & IREFB
HMC714LP5E also provides two reference voltage outputs, IREFA (pin 26) and IREFB (pin 15) for A & B channels,
which when used with the INSA/INSB outputs allows cancellation of temperature and supply related variations of the
INSA/INSB DC offsets. INSA/INSB DC offsets are equal to the IREFA/IREFB reference voltages, and these levels
corresponds to the envelope-to-average ratio (EAR) or peak-to-average ratio (PAR) of an unmodulated carrier (CW-
tone crest factor = 3 dB). For the best cancellation of the effects of temperature and supply voltage on INSA/INSB DC
offsets, load both the INSA/INSB and IREFA/IREFB outputs with an equivalent RC network.
Propagation Delay of INSA & INSB
The proper operation of the iPAR feature depends on
the proper settling of the RMS outputs because both
the iPAR feature and the RMS detection feature share
the same internal structures. After internal mechanisms
of the detector have settled, the RMS outputs (RMSA &
RMSB) provide a reading of input average power while
iPAR outputs (INSA & INSB) provides the instantaneous
(or peak) power value of the input signal. There is of
course some finite propagation delay from the instant of
input power change to the change of INSA (INSB). That
propagation delay is defined by the external capacitor,
Cext. The figure illustrates the propagation delay from a
900 MHz, 6-tone (multi-carrier) input signal at -10 dBm
average power to the INSA output of HMC714LP5E. As
illustrated, the propagation delay is 26 nsec with the
detector configured with the wideband, single-ended
input interface. The use of the differential input interface
with the balun increases the propagation delay to 37
nsec under similar test conditions.
PAR – Envelope Power Normalized To Average Power (Continued)
-0.2
-0.15
-0.1
-0.05
0
0.05
0.1
0.15
0.2
0
0.36
0.71
1.07
1.42
1.78
2.14
2.49
2.85
-150
-100
-50
0
50
100
150
200
250
Input
Signal
Envelope
(V)
INSA
(V)
Vpd (Vdc)
26nS
Propagation Delay with Wideband
Single Ended Input Interface
HMC714LP5 / 714LP5E
v07.1109
DUAL RMS POWER DETECTOR
0.1 - 5.8 GHz
相關PDF資料 |
PDF描述 |
|---|---|
| HMC742LP5 | 70 MHz - 4000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| HMC770LP4BE | 40 MHz - 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| HMC789ST89E | 700 MHz - 2800 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| HMC815LC5 | 21000 MHz - 27000 MHz RF/MICROWAVE UP CONVERTER |
| HMC909LP4E | 0 MHz - 5800 MHz RF/MICROWAVE LINEAR DETECTOR, 10 dBm INPUT POWER-MAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC7150LP3DE | 功能描述:RF Modulator IC 16-VFQFN Exposed Pad 制造商:analog devices inc. 系列:- 包裝:剪帶 零件狀態:有效 功能:- LO 頻率:- RF 頻率:- P1dB:- 本底噪聲:* 輸出功率:- 電流 - 電源:- 電壓 - 電源:6V 測試頻率:- 封裝/外殼:16-VFQFN 裸露焊盤 標準包裝:1 |
| HMC715LP3 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 2.1 - 2.9 GHz |
| HMC715LP3E | 制造商:Hittite Microwave Corp 功能描述:IC MMIC AMP LNA PHEMT 16-QFN |
| HMC716LP3 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 3.1 - 3.9 GHz |
| HMC716LP3E | 制造商:Hittite Microwave Corp 功能描述:IC MMIC AMP LNA PHEMT 16-QFN |
發布緊急采購，3分鐘左右您將得到回復。