- 您現在的位置：買賣IC網 > PDF目錄370645 > HN29W12811 (Hitachi,Ltd.) 128M AND type Flash Memory More than 8,029-sector (135,657,984-bit) PDF資料下載
參數資料
| 型號： | HN29W12811 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | 128M AND type Flash Memory More than 8,029-sector (135,657,984-bit) |
| 中文描述： | 128M的超過8029型快閃記憶體部門（135657984位） |
| 文件頁數： | 9/42頁 |
| 文件大小： | 315K |
| 代理商： | HN29W12811 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
HN29W12811 Series
9
Fifth bus cycle
Sixth bus cycle
Command
Bus
cycles
Operation
mode
Data in
Operation
mode
Data in
Read
Serial read (1) (Without CA)
3
(With CA)
3 + 2h*
6
Write
CA (2)*
5
Serial read (2)
3
Read identifier codes
1
Data recovery read
1
Auto erase
Single sector
4
Auto program Program (1)
(Without
CA*
7
)
4
(With CA*
7
)
4 + 2h*
6
Write
CA (2)*
5
Write
40H
*11, 12
Program (2)*
10
4
Program (3) (Control bytes)*
7
4
Program (4)
(WithoutCA*
7
) 4
(With CA*
7
)
4 + 2h*
6
Write
CA (2)
Write
40H
*11, 12
Reset
1
Clear status register
1
Data recovery write
Notes: 1. Commands and sector address are latched at rising edge of
WE
pulses. Program data is latched
at rising edge of SC pulses.
2. The chip is in the read status register mode when
RES
is set to V
IHR
first time after the power up.
3. Refer to the command read and write mode in mode selection.
4. SA (1) = Sector address (A0 to A7), SA (2) = Sector address (A8 to A12).
5. CA (1) = Column address (A0 to A7), CA (2) = Column address (A8 to A11).
(0
≤
A11 to A0
≤
83FH)
6. The variable h is the input number of times of set of CA (1) and CA (2) (1
≤
h
≤
2048 + 64).
Set of CA (1) and CA (2) can be input without limitation.
7. By using program (1) and (3), data can additionally be programmed maximum 15 times for each
sector before erase.
8. ID = Identifier code; Manufacturer code (07H), Device code (95H).
9. The manufacturer identifier code is output when
CDE
is low and the device identifier code is output
when
CDE
is high.
10.Before program (2) operations, data in the programmed sector must be erased.
11.No commands can be written during auto program and erase (when the RDY/
Busy
pin outputs a
V
OL
).
12.The fourth or sixth cycle of the auto program comes after the program data input is complete.
4
相關PDF資料 |
PDF描述 |
|---|---|
| HN29W12814A | 128M AND type Flash Memory(128M AND型閃速存儲器) |
| HN29W25611T-50 | 256M AND type Flash Memory More than 16,057-sector (271,299,072-bit) |
| HN29W25611T | 256M AND type Flash Memory More than 16,057-sector (271,299,072-bit) |
| HN29W25611T-50H | 256M AND type Flash Memory More than 16,057-sector (271,299,072-bit) |
| HN29W25611 | 256M AND type Flash Memory(256M AND型閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HN29W12811BP-60 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|AND FLASH|16896KX8|CMOS|BGA|72PIN|PLASTIC |
| HN29W12811T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash Application Design Guidelines Others |
| HN29W12811T-60 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:128M AND type Flash Memory More than 8,029-sector (135,657,984-bit) |
| HN29W12814ASERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AND Flash EEPROM |
| HN29W12814ATT-50 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|AND FLASH|2X8448KX8|CMOS|TSOP|48PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。