- 您現在的位置：買賣IC網 > PDF目錄360784 > ICS9248YF-96LF-T Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ PDF資料下載
參數資料
| 型號： | ICS9248YF-96LF-T |
| 英文描述： | Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ |
| 中文描述： | 頻率發生器 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 206K |
| 代理商： | ICS9248YF-96LF-T |
6
ICS9248-96
0311D—04/23/04
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS9248-
96 serve as dual signal functions to the device. During
initial power-up, they act as input pins. The logic level
(voltage) that is present on these pins at this time is read
and stored into a 5-bit internal data latch. At the end of
Power-On reset, (see AC characteristics for timing values),
the device changes the mode of operations for these pins
to an output function. In this mode the pins produce the
specified buffered clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD
(logic 1) power supply or the GND (logic 0) voltage
potential. A 10 Kilohm (10K) resistor is used to provide
both the solid CMOS programming voltage needed during
the power-up programming period and to provide an
insignificant load on the output clock during the subsequent
operating period.
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, then only a single resistor is necessary. The
programming resistors should be located close to the
series termination resistor to minimize the current loop
area. It is more important to locate the series termination
resistor close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS9248YF-96-T | Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ |
| ICS932S202 | Frequency Timing Generator for Differential PIIIType Dual-CPU Systems |
| ICS932S208 | Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
| ICS932S208YFLF-T | Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
| ICS932S208YGLF-T | Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS9248YF-96-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ |
| ICS9248YF-97-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Timing Generator for PENTIUM II Systems |
| ICS9248YF-98-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ |
| ICS9248YF-99 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ |
| ICS9248YG-101-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for PENTIUM/ProTM & K6 |
發布緊急采購，3分鐘左右您將得到回復。