- 您現在的位置：買賣IC網 > PDF目錄377240 > IDT5V9950PFI (INTEGRATED DEVICE TECHNOLOGY INC) Scan Test Devices With 18-Bit Bus Transceivers And Registers 64-LQFP -40 to 85 PDF資料下載
參數資料
| 型號： | IDT5V9950PFI |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | Scan Test Devices With 18-Bit Bus Transceivers And Registers 64-LQFP -40 to 85 |
| 中文描述： | 5V SERIES, PLL BASED CLOCK DRIVER, 8 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP32 |
| 封裝： | TQFP-32 |
| 文件頁數： | 3/9頁 |
| 文件大?。?/td> | 67K |
| 代理商： | IDT5V9950PFI |
3
INDUSTRIAL TEMPERATURE RANGE
IDT5V9950
3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK II JR.
Output skew with respect to the REF input is adjustable to compensate
for PCB trace delays, backplane propagation delays or to accommodate
requirements for special timng relationships between clocked compo-
nents. Skew is selectable as a multiple of a time unit (t
U
) which ranges
from625ps to 1.3ns (see Programmable Skew Range and Resolution
Table). There are nine skew configurations available for each output
pair. These configurations are chosen by the nF
1:0
control pins. In order
to mnimze the number of control pins, 3-level inputs (HIGH-MID-LOW)
are used, they are intended for but not restricted to hard-wiring. Undriven
3-level inputs default to the MID level. Where programmable skew is
not a requirement, the control pins can be left open for the zero skew
default setting. The Control Summary Table shows how to select specific
skew taps by using the nF
1:0
control pins.
PROGRAMMABLE SK EW
EX TERNAL FEEDBACK
By providing external feedback, the IDT5V9950 gives users flexibility
with regard to skew adjustment. The FB signal is compared with the
input REF signal at the phase detector in order to drive the VCO. Phase
differences cause the VCO of the PLL to adjust upwards or downwards
accordingly.
NOTES:
1. The device may be operated outside recommended frequency ranges without damage, but functional operation is not guaranteed.
2. The level to be set on FS is determned by the nomnal operating frequency of the VCO and Time Unit Generator. The VCO frequency always appears at 1Q
1:0
, 2Q
1:0
, and the
higher outputs when they are operated in their undivided modes. The frequency appearing at the REF and FB inputs will be the same as VCO when the output connected to
FB is undivided. The frequency of the REF and FB inputs will be 1/2 or 1/4 the VCO frequency when the part is configured for frequency multiplication by using a divided output
as the FB input.
3. Skew adjustment range assumes that a zero skew output is used for feedback. If a skewed Q output is used for feedback, then adjustment range will be greater. For example
if a 4t
U
skewed output is used for feedback, all other outputs will be skewed –4t
U
in addition to whatever skew value is programmed for those outputs. ‘Max adjustment’ range
applies to output pairs 3 and 4 where ± 6t
U
skew adjustment is possible and at the lowest F
NOM
value.
An internal loop filter moderates the response of the VCO to the
phase detector. The loop filter transfer function has been chosen to
provide mnimal jitter (or frequency variation) while still providing accu-
rate responses to input frequency changes.
FS = LOW
1/(32 x F
NOM
)
24 to 50MHz
FS = MID
1/(16 x F
NOM
)
48 to 100MHz
FS = HIGH
1/(8 x F
NOM
)
96 to 200MHz
Comments
Timng Unit Calculation (t
U
)
VCO Frequency Range (F
NOM
)
(1,2)
Skew Adjustment Range
(3)
Max Adjustment:
±7.8125ns
±67.5°
±18.75%
t
U
= 1.25ns
t
U
= 0.833ns
t
U
= 0.625ns
—
—
—
—
±7.8125ns
±135°
±37.5%
—
—
t
U
= 1.25ns
t
U
= 0.833ns
t
U
= 0.625ns
—
—
±7.8125ns
±270°
±75%
—
—
—
—
t
U
= 1.25ns
t
U
= 0.833ns
t
U
= 0.625ns
ns
Phase Degrees
% of Cycle Time
Example 1, F
NOM
= 25MHz
Example 2, F
NOM
= 37.5MHz
Example 3, F
NOM
= 50MHz
Example 4, F
NOM
= 75MHz
Example 5, F
NOM
= 100MHz
Example 6, F
NOM
= 150MHz
Example 7, F
NOM
= 200MHz
PROGRAMMABLE SK EW RANGE AND RESOLUTION TABLE
相關PDF資料 |
PDF描述 |
|---|---|
| IDT5V9955 | Scan Test Devices With 18-Bit Bus Transceivers And Registers 64-LQFP -40 to 85 |
| IDT5V995 | 3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK |
| IDT5V995PFGI | 3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK |
| IDT5V995PFI | 3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK |
| IDT6116 | CMOS STATIC RAM 16K (2K x 8 BIT) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT5V9955BFGI | 功能描述:IC CLK DVR PLL 3.3 PROGR 96FBGA RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:TurboClock™ W 標準包裝:27 系列:Precision Edge® 類型:頻率合成器 PLL:是 輸入:PECL，晶體 輸出:PECL 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/是 頻率 - 最大:800MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 5.25 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| IDT5V9955BFGI8 | 功能描述:IC CLK DVR PLL 3.3 PROGR 96FBGA RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:TurboClock™ W 標準包裝:27 系列:Precision Edge® 類型:頻率合成器 PLL:是 輸入:PECL，晶體 輸出:PECL 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/是 頻率 - 最大:800MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 5.25 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| IDT5V9955BFI | 制造商:Integrated Device Technology Inc 功能描述: |
| IDT5V995PFGI | 功能描述:IC CLK DVR PLL 3.3V PROGR 44TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:TurboClock™ II 標準包裝:27 系列:Precision Edge® 類型:頻率合成器 PLL:是 輸入:PECL，晶體 輸出:PECL 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/是 頻率 - 最大:800MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 5.25 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| IDT5V995PFGI8 | 功能描述:IC CLK DVR PLL 3.3V PROGR 44TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:TurboClock™ II 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
發布緊急采購，3分鐘左右您將得到回復。