IDT72T1845/55/65/75/85/95/105/115/125 2.5V TeraSync 18-BIT/9-BIT FIFO
參數資料
型號： IDT72T18125L4-4BB
廠商： IDT, Integrated Device Technology Inc
文件頁數： 9/55頁
文件大小： 0K
描述： IC FIFO 524X18 2.5V 4NS 240BGA
標準包裝： 1
系列： 72T
功能： 異步，同步
存儲容量： 9M（512K x 18）
數據速率： 10MHz
訪問時間： 3.4ns
電源電壓： 2.375 V ~ 2.625 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 240-BGA
供應商設備封裝： 240-PBGA（19x19）
包裝： 托盤
其它名稱： 72T18125L4-4BB
17
COMMERCIALANDINDUSTRIAL
TEMPERATURERANGES
IDT72T1845/55/65/75/85/95/105/115/125 2.5V TeraSync 18-BIT/9-BIT FIFO 2Kx18/4Kx9, 4Kx18/
8Kx9, 8Kx18/16Kx9, 16Kx18/32Kx9, 32Kx18/64Kx9, 64Kx18/128Kx9, 128Kx18/256Kx9, 256Kx18/512Kx9, 512Kx18/1Mx9
FEBRUARY 10, 2009
IDT72T18125.Ifbothx9Inputandx9OutputbusWidthsareselected,D=4,097
writes for the IDT72T1845, 8,193 writes for the IDT72T1855, 16,385 writes
for the IDT72T1865, 32,769 writes for the IDT72T1875, 65,537 writes for the
IDT72T1885, 131,073 writes for the IDT72T1895, 262,145 writes for the
IDT72T18105, 524,289 writes for the IDT72T18115 and 1,048,577 writes for
the IDT72T18125, respectively. Note that the additional word in FWFT mode
is due to the capacity of the memory plus output register.
If the FIFO is full, the first read operation will cause the
IR flag to go LOW.
Subsequent read operations will cause the
PAF and HF to go HIGH at the
conditions described in Table 4. If further read operations occur, without write
operations,the
PAEwillgoLOWwhentherearen+1wordsintheFIFO,where
n is the empty offset value. Continuing read operations will cause the FIFO to
become empty. When the last word has been read from the FIFO,
OR will go
HIGH inhibiting further read operations.
REN is ignored when the FIFO is
empty.
When configured in FWFT mode, the
OR flag output is triple register-
buffered, and the
IR flag output is double register-buffered.
Relevant timing diagrams for FWFT mode can be found in Figure 14, 15,
16 and 19.
PROGRAMMING FLAG OFFSETS
FullandEmptyFlagoffsetvaluesareuserprogrammable.TheIDT72T1845/
72T1855/72T1865/72T1875/72T1885/72T1895/72T18105/72T18115/
72T18125haveinternalregistersfortheseoffsets.Thereareeightdefaultoffset
valuesselectableduringMasterReset.TheseoffsetvaluesareshowninTable
2.OffsetvaluescanalsobeprogrammedintotheFIFOinoneoftwoways;serial
or parallel loading method. The selection of the loading method is done using
the
LD (Load) pin. During Master Reset, the state of the LD input determines
whether serial or parallel flag offset programming is enabled. A HIGH on
LD
duringMasterResetselectsserialloadingofoffsetvalues.ALOWon
LDduring
Master Reset selects parallel loading of offset values.
In addition to loading offset values into the FIFO, it is also possible to read
the current offset values. Offset values can be read via the parallel output port
Q0-Qn, regardless of the programming mode selected (serial or parallel). It is
not possible to read the offset values in serial fashion.
Figure3,ProgrammableFlagOffsetProgrammingSequence,summaries
thecontrolpinsandsequenceforbothserialandparallelprogrammingmodes.
For a more detailed description, see discussion that follows.
The offset registers may be programmed (and reprogrammed) any time
after Master Reset, regardless of whether serial or parallel programming has
been selected. Valid programming ranges are from 0 to D-1.
SYNCHRONOUS vs ASYNCHRONOUS PROGRAMMABLE FLAG
TIMING SELECTION
The IDT72T1845/72T1855/72T1865/72T1875/72T1885/72T1895/
72T18105/72T18115/72T18125 can be configured during the Master Reset
cycle with either synchronous or asynchronous timing for
PAFand PAEflags
by use of the PFM pin.
If synchronous
PAF/PAE configuration is selected (PFM, HIGH during
MRS),thePAFisassertedandupdatedontherisingedgeofWCLKonlyand
not RCLK. Similarly,
PAEisassertedandupdatedontherisingedgeofRCLK
onlyandnotWCLK.Fordetailtimingdiagrams,seeFigure23forsynchronous
PAF timing and Figure 24 for synchronous PAE timing.
If asynchronous
PAF/PAE configuration is selected (PFM, LOW during
MRS),thePAFisassertedLOWontheLOW-to-HIGHtransitionofWCLKand
PAFisresettoHIGHontheLOW-to-HIGHtransitionofRCLK.Similarly,PAE
isassertedLOWontheLOW-to-HIGHtransitionofRCLK.
PAEisresettoHIGH
ontheLOW-to-HIGHtransitionofWCLK.Fordetailtimingdiagrams,seeFigure25
for asynchronous
PAF timing and Figure 26 for asynchronous PAE timing.
(4,097-m) writes for the IDT72T1855, (8,193-m) writes for the IDT72T1865,
(16,385-m) writes for the IDT72T1875, (32,769-m) writes for the IDT72T1885,
(65,536-m)writesfortheIDT72T1895,(131,073-m)writesfortheIDT72T18105,
(262,145-m) writes for the IDT72T18115 and (524,289-m) writes for the
IDT72T18125. If both x9 Input and x9 Output bus Widths are selected, (D-m)
= (4,097-m) writes for the IDT72T1845, (8,193-m) writes for the IDT72T1855,
(16,385-m) writes for the IDT72T1865, (32,769-m) writes for the IDT72T1875,
(65,537-m)writesfortheIDT72T1885,(131,073-m)writesfortheIDT72T1895,
(262,145-m) writes for the IDT72T18105, (524,289-m) writes for the
IDT72T18115 and (1,048,577-m) writes for the IDT72T18125. The offset m
isthefulloffsetvalue.Thedefaultsettingforthesevaluesarestatedinthefootnote
of Table 2.
WhentheFIFOisfull,theInputReady(
IR)flagwillgoHIGH,inhibitingfurther
write operations. If no reads are performed after a reset,
IR will go HIGH after
DwritestotheFIFO.Ifx18Inputorx18OutputbusWidthisselected,D = 2,049
writes for the IDT72T1845, 4,097 writes for the IDT72T1855, 8,193 writes for
the IDT72T1865, 16,385 writes for the IDT72T1875, 32,769 writes for the
IDT72T1885, 65,536 writes for the IDT72T1895, 131,073 writes for the
IDT72T18105,262,145writesfortheIDT72T18115and524,289writesforthe
TABLE 2 — DEFAULT PROGRAMMABLE
FLAG OFFSETS
NOTES:
1. n = empty offset for
PAE.
2. m = full offset for
PAF.
3. As well as selecting serial programming mode, one of the default values will also
be loaded depending on the state of FSEL0 & FSEL1.
4. As well as selecting parallel programming mode, one of the default values will
also be loaded depending on the state of FSEL0 & FSEL1.
IDT72T1845
Offsets n,m
All Other
x9 to x9
*
LD
FSEL1
FSEL0
Modes
Mode
LH
L
511
L
H
255
L
127
LH
H
63
H
L
31
1,023
HH
L
15
31
HL
H
7
15
HHH
3
7
IDT72T1855, 72T1865, 72T1875, 72T1885,
72T1895, 72T18105, 72T18115, 72T18125
*
LD
FSEL1
FSEL0
Offsets n,m
H
L
1,023
LH
L
511
L
H
255
LLL
127
LH
H
63
HH
L
31
HL
H
15
HHH
7
*
LD
FSEL1
FSEL0
Program Mode
H
X
Serial(3)
L
X
Parallel(4)
*THIS PIN MUST BE HIGH AFTER MASTER RESET TO WRITE
OR READ DATA TO/FROM THE FIFO MEMORY.
相關PDF資料
PDF描述
IDT72T36125L5BBI IC FIFO 524X18 5NS 240BGA
IDT72T36135ML5BBG IC FIFO 1MX18 5NS 240BGA
IDT72T72115L5BBI IC FIFO 131072X72 5NS 324-BGA
IDT72V06L15J IC ASYNCH 8192X18 15NS 32PLCC
IDT72V2105L15PFI IC FIFO SUPERSYNCII 15NS 64-TQFP
相關代理商/技術參數
參數描述
IDT72T18125L4-4BBG 功能描述:IC FIFO 524X18 2.5V 4NS 240BGA RoHS:是 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72T 標準包裝:90 系列:74ABT 功能:同步，雙端口 存儲容量:4.6K（64 x 36 x2） 數據速率:67MHz 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:120-LQFP 裸露焊盤 供應商設備封裝:120-HLQFP（14x14） 包裝:托盤 產品目錄頁面:1005 (CN2011-ZH PDF) 其它名稱:296-3984
IDT72T18125L5BB 功能描述:IC FIFO 524X18 2.5V 5NS 240BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72T 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72T18125L5BBGI 制造商:Integrated Device Technology Inc 功能描述:IC FIFO 524X18 2.5V 5NS 240BGA
IDT72T18125L5BBI 功能描述:IC FIFO 524X18 2.5V 5NS 240BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72T 標準包裝:90 系列:74ABT 功能:同步，雙端口 存儲容量:4.6K（64 x 36 x2） 數據速率:67MHz 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:120-LQFP 裸露焊盤 供應商設備封裝:120-HLQFP（14x14） 包裝:托盤 產品目錄頁面:1005 (CN2011-ZH PDF) 其它名稱:296-3984
IDT72T18125L6-7BB 功能描述:IC FIFO 524X18 2.5V 6-7NS 240BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72T 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*