參數資料
型號： IDT82P2816BB
廠商： IDT, Integrated Device Technology Inc
文件頁數： 79/146頁
文件大?。?/td> 0K
描述： IC LIU T1/J1/E1 16+1CH 416-PBGA
標準包裝： 5
功能： 線路接口單元（LIU）
接口： E1，J1，T1
電路數： 1
電源電壓： 1.8V, 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 416-BGA
供應商設備封裝： 416-PBGA（27x27）
包裝： 托盤
包括： 缺陷和警報檢測，驅動器過流檢測和保護，LLOS 檢測，PRBSARB / IB 檢測和生成
其它名稱： 82P2816BB
IDT82P2816
16(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Functional Description
38
February 6, 2009
3.5
DIAGNOSTIC FACILITIES
The diagnostic facilities include:
BPV (Bipolar Violation) / CV (Code Violation) detection and BPV
insertion;
EXZ (Excessive Zero) detection;
LOS (Loss Of Signal) detection;
AIS (Alarm Indication Signal) detection and generation;
Pattern generation and detection, including PRBS (Pseudo Ran-
dom Bit Sequence), ARB (Arbitrary Pattern) and IB (Inband Loop-
back).
The above defects, alarms or patterns can be counted by an internal
Error Counter, indicated by the respective interrupt bit and indicated by
RMFn or TMFn.
For diagnostic purposes, loopbacks and channel 0 monitoring can
also be implemented.
3.5.1
BIPOLAR VIOLATION (BPV) / CODE VIOLATION (CV)
DETECTION AND BPV INSERTION
3.5.1.1 Bipolar Violation (BPV) / Code Violation (CV) Detection
BPV/CV is monitored in both the receive path and the transmit path.
BPV is detected when the data is AMI coded and CV is detected when
the data is B8ZS/HDB3 coded. If the transmit system interface is in
Transmit Single Rail NRZ Format mode, the BPV/CV detection is
disabled in the transmit path automatically.
A BPV is detected when two consecutive pulses of the same polarity
are received.
A CV is detected when two consecutive BPVs of the same polarity
that are not a part of the B8ZS/HDB3 zero substitution are received.
When BPV/CV is detected in the receive path, the Line Bipolar Viola-
tion LBPV_IS bit (b4, INTS2,...) will be set and an interrupt will be
reported by INT if not masked by the LBPV_IM bit (b4, INTM2,...).
When BPV/CV is detected in the transmit path, the System Bipolar
Violation SBPV_IS bit (b5, INTS2,...) will be set and an interrupt will be
reported by INT if not masked by the SBPV_IM bit (b5, INTM2,...).
BPV/CV may be counted by an internal Error Counter or may be indi-
cated by the RMFn or TMFn pin. Refer to Section 3.5.6 Error Counter
Indication respectively.
3.5.1.2 Bipolar Violation (BPV) Insertion
The BPV can only be inserted in the transmit path.
A BPV will be inserted on the next available mark in the data stream
to be transmitted by writing a ‘1’ to the BPV_INS bit (b6, ERR,...). This
bit will be reset once BPV insertion is done.
3.5.2
EXCESSIVE ZEROES (EXZ) DETECTION
EXZ is monitored in both the receive path and the transmit path.
Different line code has different definition of the EXZ. The
IDT82P2816 provides two standards of EXZ definition for each kind of
line code rule. The standards are ANSI and FCC, as selected by the
EXZ_DEF bit (b7, ERR,...). Refer to Table-16 for details.
When EXZ is detected in the receive path, the LEXZ_IS bit (b2,
INTS2,...) will be set and an interrupt will be reported by INT if not
masked by the LEXZ_IM bit (b2, INTM2,...).
When EXZ is detected in the transmit path, the SEXZ_IS bit (b3,
INTS2,...) will be set and an interrupt will be reported by INT if not
masked by the SEXZ_IM bit (b3, INTM2,...).
Table-16 EXZ Definition
Line Code
Rule
Definition
ANSI (EXZ_DEF = 0)
FCC (EXZ_DEF = 1)
AMI
An EXZ is detected when
any string of more than 15
consecutive
‘0’s
are
received.
T1/J1 - An EXZ is detected
when any string of more
than 80 consecutive ‘0’s are
received.
E1 - An EXZ is detected
when any string of more
than 15 consecutive ‘0’s are
received.
B8ZS
An EXZ is detected when
any string of more than 7
consecutive
‘0’s
are
received.
An EXZ is detected when
any string of more than 7
consecutive
‘0’s
are
received.
HDB3
An EXZ is detected when
any string of more than 3
consecutive
‘0’s
are
received.
An EXZ is detected when
any string of more than 3
consecutive
‘0’s
are
received.
Note:
If the transmit system interface is in Transmit Single Rail NRZ Format mode, the EXZ is
detected according to the standard of AMI.
相關PDF資料
PDF描述
VI-201-IY-F2 CONVERTER MOD DC/DC 12V 50W
VI-B3Y-IW-B1 CONVERTER MOD DC/DC 3.3V 66W
AS2540 IC TELEPHONE CMOS MULTIFU 28SOIC
VI-B3Y-IV-S CONVERTER MOD DC/DC 3.3V 99W
VI-200-IY-F3 CONVERTER MOD DC/DC 5V 50W
相關代理商/技術參數
參數描述
IDT82P2816BBG 功能描述:IC LINE INTERFACE UNIT 416-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2821 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:21(+1) Channel High-Density T1/E1/J1 Line Interface Unit
IDT82P2821BH 功能描述:IC LIU T1/J1/E1 21+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2821BHG 功能描述:IC LINE INTERFACE UNIT 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2828 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:28(+1) Channel High-Density T1/E1/J1 Line Interface Unit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*