參數資料
型號: IDT82P2816BB
廠商: IDT, Integrated Device Technology Inc
文件頁數: 83/146頁
文件大?。?/td> 0K
描述: IC LIU T1/J1/E1 16+1CH 416-PBGA
標準包裝: 5
功能: 線路接口單元(LIU)
接口: E1,J1,T1
電路數: 1
電源電壓: 1.8V, 3.3V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 416-BGA
供應商設備封裝: 416-PBGA(27x27)
包裝: 托盤
包括: 缺陷和警報檢測,驅動器過流檢測和保護,LLOS 檢測,PRBSARB / IB 檢測和生成
其它名稱: 82P2816BB
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
IDT82P2816
16(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Functional Description
41
February 6, 2009
3.5.3.3 Transmit LOS (TLOS)
The amplitude and density of the data output on the transmit line side
are monitored. When the amplitude of the data is less than a certain
voltage for a certain period, TLOS is declared. The voltage is defined by
the TALOS[1:0] bits (b3~2, LOS,...). The period is defined by the
TDLOS[1:0] bits (b1~0, LOS,...). When a valid pulse is detected, i.e., the
amplitude is above the setting in the TALOS[1:0] bits (b3~2, LOS,...),
TLOS is cleared.
When TLOS is detected, the TLOS_S bit (b2, STAT0,...) will be set. A
transition from ‘0’ to ‘1’ on the TLOS_S bit (b2, STAT0,...) or any transi-
tion (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the TLOS_S bit (b2, STAT0,...) will
set the TLOS_IS bit (b2, INTS0,...) to ‘1’, as selected by the TLOS_IES
bit (b2, INTES,...). When the TLOS_IS bit (b2, INTS0,...) is ‘1’, an inter-
rupt will be reported by INT if not masked by the TLOS_IM bit (b2,
TLOS may be counted by an internal Error Counter or may be indi-
cated by the TMFn pin. Refer to Section 3.5.6 Error Counter and
TLOS can be used to monitor the LOS in the transmit line side
between two channels. The connection between the two channels is
shown in Figure-21. The two channels can be of the same device or
different devices on the premises that the transmit line interfaces are in
the same mode and at least the output of one channel is in High-Z state.
Table-19 lists each results in this case. In the left two columns, the OE
bit (b6, TCF0,...) of the two channels controls the output status in the
transmit line side to ensure that at least one channel is in High-Z state.
The middle two columns list the internal operation status. In the right two
columns, the TLOS_S bit (b2, STAT0,...) of the two channels indicates
the TLOS status in the transmit line side.
Figure-21 TLOS Detection Between Two Channels
Line
Driver
TLOS
Line
Driver
TLOS
TTIPn
TRINGn
TTIPn
TRINGn
Channel #1
Channel #2
TLOS
Detector
TLOS
Detector
Table-19 TLOS Detection Between Two Channels
Output Status ~ Controlled By the OE Bit
Internal Operation Status
TLOS Status ~ Indicated By the TLOS_S Bit
Channel #1
Channel #2
Channel #1
Channel #2
Channel #1
Channel #2
Normal ~ 1
High-Z ~ 0
Normal
(don’t-care)
No TLOS ~ 0
Normal ~ 1
High-Z ~ 0
Failure
Normal
TLOS Detected ~ 1 *
TLOS Detected ~ 1
High-Z ~ 0
Normal ~ 1
(don’t-care)
Normal
No TLOS ~ 0
High-Z ~ 0
Normal ~ 1
Normal
Failure
TLOS Detected ~ 1
TLOS Detected ~ 1 *
High-Z ~ 0
(don’t-care)
TLOS Detected ~ 1
Note:
* The TLOS_S bit (b2, STAT0,...) may not be set if there is any catastrophic failure in the channel.
相關PDF資料
PDF描述
VI-201-IY-F2 CONVERTER MOD DC/DC 12V 50W
VI-B3Y-IW-B1 CONVERTER MOD DC/DC 3.3V 66W
AS2540 IC TELEPHONE CMOS MULTIFU 28SOIC
VI-B3Y-IV-S CONVERTER MOD DC/DC 3.3V 99W
VI-200-IY-F3 CONVERTER MOD DC/DC 5V 50W
相關代理商/技術參數
參數描述
IDT82P2816BBG 功能描述:IC LINE INTERFACE UNIT 416-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2821 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:21(+1) Channel High-Density T1/E1/J1 Line Interface Unit
IDT82P2821BH 功能描述:IC LIU T1/J1/E1 21+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2821BHG 功能描述:IC LINE INTERFACE UNIT 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2828 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:28(+1) Channel High-Density T1/E1/J1 Line Interface Unit