- 您現在的位置：買賣IC網 > PDF目錄16312 > ISL51002-EVALZ (Intersil)EVAL BOARD FOR ISL51002 PDF資料下載
參數資料
| 型號： | ISL51002-EVALZ |
| 廠商： | Intersil |
| 文件頁數： | 16/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR ISL51002 |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
23
FN6164.3
February 29, 2012
Technical Highlights
The ISL51002 provides all the features of traditional triple
channel video AFEs, but adds several next-generation
enhancements, bringing performance and ease of use to
new levels.
DPLL
All video AFEs must phase lock to an HSYNC signal,
supplied either directly or embedded in the video stream
(Sync On Green). Historically this has been implemented as
a traditional analog PLL. At SXGA and lower resolutions, an
analog PLL solution has proven adequate, if somewhat
troublesome (due to the need to adjust charge pump
currents, VCO ranges and other parameters to find the
optimum trade-off for a wide range of pixel rates).
As display resolutions and refresh rates have increased,
however, the pixel period has shrunk. An XGA pixel at a
60Hz refresh rate has 15.4ns to change and settle to its new
value. But at UXGA 75Hz, the pixel period is 4.9ns. Most
consumer graphics cards (even the ones with “350MHz”
DACs) spend most of that time slewing to the new pixel
value. The pixel may settle to its final value with 1ns or less
before it begins slewing to the next pixel. In many cases it
rings and never settles at all. So precision, low-jitter
sampling is a fundamental requirement at these speeds, and
a difficult one for an analog PLL to meet.
The ISL51002's DPLL has less than 250ps of jitter, peak to
peak, and independent of the pixel rate. The DPLL generates
64 phase steps per pixel (vs. the industry standard 32), for
fine, accurate positioning of the sampling point. The crystal-
locked NCO inside the DPLL completely eliminates drift due to
charge pump leakage, so there is inherently no frequency or
phase change across a line. An intelligent all-digital loop
filter/controller eliminates the need for the user to have to
program or change anything (except for the number of pixels)
to lock over a range from interlaced video (10MHz or higher)
to UXGA 60Hz (165MHz, with the ISL51002-165).
The DPLL eliminates much of the performance limitations and
complexity associated with noise-free digitization of high
speed signals.
Automatic Black Level Compensation (ABLC)
and Gain Control
Traditional video AFEs have an offset DAC prior to the ADC,
to both correct for offsets on the incoming video signals and
add/subtract an offset for user “brightness control” without
sacrificing the 10-bit dynamic range of the ADC. This
solution is adequate, but it places significant requirements
on the system's firmware, which must execute a loop that
detects the black portion of the signal and then servos the
offset DACs until that offset is nulled (or produces the
desired ADC output code). Once this has been
accomplished, the offset (both the offset in the AFE and the
offset of the video card generating the signal) is subject to
drift, the temperature inside a monitor or projector can easily
change +50°C between power-on/offset calibration on a cold
morning and the temperature reached once the monitor and
the monitor's environment have reached steady state. Offset
can drift significantly over +50°C, reducing image quality and
requiring that the user do a manual calibration once the
monitor has warmed up.
In addition to drift, many AFEs exhibit interaction between
the offset and gain controls. When the gain is changed, the
magnitude of the offset is changed as well. This again
increases the complexity of the firmware as it tries to
optimize gain and offset settings for a given video input
signal. Instead of adjusting just the offset, then the gain, both
have to be adjusted interactively until the desired ADC
output is reached.
The ISL51002 simplifies offset and gain adjustment and
completely eliminates offset drift using its Automatic Black
Level Compensation (ABLC) function. ABLC monitors the
black level and continuously adjusts the ISL51002's 10-bit
offset DACs to null out the offset. Any offset, whether due to
the video source or the ISL51002's analog amplifiers, is
eliminated with 10-bit accuracy. Any drift is compensated for
well before it can have a visible effect. Manual offset
adjustment control is still available (a 10-bit register allows the
firmware to adjust the offset ±64 codes in exactly 1ADC LSB
increments). Gain is now completely independent of offset
(adjusting the gain no longer affects the offset, so there is no
longer a need to program the firmware to cope with interactive
offset and gain controls).
Finally, there should be no concerns over ABLC itself
introducing visible artifacts; it doesn't. ABLC functions at a
very low frequency, changing the offset in 1 LSB increments,
so it can't cause visible brightness fluctuations. And once
ABLC is locked, if the offset doesn't drift, the DACs won't
change. If desired, ABLC can be disabled, allowing the
firmware to work in the traditional way, with 10-bit offset
DACs under the firmware's control.
Gain and Offset Control
To simplify image optimization algorithms, the ISL51002
features fully-independent gain and offset adjustment.
Changing the gain does not affect the DC offset, and the
weight of an Offset DAC LSB does not vary depending on
the gain setting.
The full-scale gain is set in the three sets of registers (0x12
and 0x13 - 0x16 and 0x17). Each set of gain registers is
divided into an 8-bit MSB register (0x12, 0x14 and 0x16) and
a 2-bit LSB register providing a 10-bit gain value that both
allows for 8-bit control compatible with the 8-bit family of
AFEs and allows for the expansion of the gain resolution in
future AFEs without significant firmware changes. The
ISL51002 can accept input signals with amplitudes ranging
from 0.35VP-P to 1.4VP-P.
ISL51002
相關PDF資料 |
PDF描述 |
|---|---|
| M3CKK-2006R | IDC CABLE - MKC20K/MC20M/MPK20K |
| 2-6754410-7 | CA,XG,MTRJ-SC |
| M3AKK-2006R | IDC CABLE - MSC20K/MC20M/MPK20K |
| H1CXS-6436M | IDC CABLE - HKC64S/AE64M/X |
| M1RXK-1640K | IDC CABLE - MPR16K/MC16F/X |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL5100A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad 18V Pin Electronics Driver/Window Comparator |
| ISL5101IB | 制造商:Intersil Corporation 功能描述: |
| ISL5120 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL5120CB | 功能描述:IC SWITCH DUAL SPST 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態(tài)電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| ISL5120CB-T | 功能描述:IC SWITCH DUAL SPST 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態(tài)電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
發(fā)布緊急采購，3分鐘左右您將得到回復。