參數資料
型號: ISL54100AHDMI-EVALZ
廠商: Intersil
文件頁數: 10/21頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR ISL54100AHDMI
標準包裝: 1
系列: *
18
FN6725.0
June 17, 2008
The ISL5410xA has a 7-bit address on the serial bus,
determined by the ADDR0-ADDR6 bits. This allows up to
128 ISL5410xAs to be independently controlled by the same
serial bus.
The bus is nominally inactive, with SDA and SCL high.
Communication begins when the host issues a START
command by taking SDA low while SCL is high (Figure 14).
The ISL5410xA continuously monitors the SDA and SCL
lines for the start condition and will not respond to any
command until this condition has been met. The host then
transmits the 7-bit serial address plus a R/W bit, indicating if
the next transaction will be a Read (R/W = 1) or a Write (R/W
= 0). If the address transmitted matches that of any device
on the bus, that device must respond with an
ACKNOWLEDGE (Figure 15).
Once the serial address has been transmitted and
acknowledged, one or more bytes of information can be
written to or read from the slave. Communication with the
selected device in the selected direction (read or write) is
ended by a STOP command, where SDA rises while SCL is
high (Figure 14), or a second START command, which is
commonly used to reverse data direction without
relinquishing the bus.
Data on the serial bus must be valid for the entire time SCL
is high (Figure 16). To achieve this, data being written to the
ISL5410xA is latched on a delayed version of the rising edge
of SCL. SCL is delayed and deglitched inside the ISL5410xA
for three crystal clock periods (120ns for a 25MHz crystal) to
eliminate spurious clock pulses that could disrupt serial
communication.
When the contents of the ISL5410xA are being read, the
SDA line is updated after the falling edge of SCL, delayed
and deglitched in the same manner.
Configuration Register Write
Figure 17 shows two views of the steps necessary to write
one or more words to the Configuration Register.
Configuration Register Read
Figure 18 shows two views of the steps necessary to read
one or more words from the Configuration Register.
SCL
SDA
START
STOP
FIGURE 14. VALID START AND STOP CONDITIONS
SCL FROM
HOST
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
8
1
9
START
ACKNOWLEDGE
FIGURE 15. ACKNOWLEDGE RESPONSE FROM RECEIVER
SCL
SDA
DATA STABLE
DATA CHANGE
DATA STABLE
FIGURE 16. VALID DATA CHANGES ON THE SDA BUS
ISL54100A, ISL54101A, ISL54102A
相關PDF資料
PDF描述
ESA14DRSN-S288 CONN EDGECARD 28POS .125 EXTEND
EMA14DRSN-S288 CONN EDGECARD 28POS .125 EXTEND
ISL59119IBZ-EVALZ EVAL BOARD FOR ISL59119IBZ
2-1906014-3 CA 2.0MM OFNR 50/125,LC SEC YEL
ESA14DRSD-S288 CONN EDGECARD 28POS .125 EXTEND
相關代理商/技術參數
參數描述
ISL54100CQZ 功能描述:IC REGENERATOR TMDS 4:1 128-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
ISL54100CQZ-EVAL 制造商:Intersil Corporation 功能描述:ISL54100CQZ-EVAL EVALUATION BOARD - Bulk
ISL54100CQZ-EVALZ 制造商:Intersil Corporation 功能描述:EVAL BD FOR ISL54100 TMDS REGENERATORS W/ MLTPLXRS - Bulk
ISL54100-EVM 制造商:Intersil Corporation 功能描述:An Evaluation Board of Manual, automatic and infrared remote control,4:1 HDMI interface, and a CD of development files 制造商:Intersil Corporation 功能描述:An Evaluation Board of Manual, automatic and infrared remote control4:1 HDMI interface, and a CD of development files
ISL54100HDMI-EVALZ 制造商:Intersil Corporation 功能描述:ISL54100HDMI EVALUATION BOARD, ROHS, 4HDMI IN, 1 HDMI OUT - Bulk