- 您現在的位置：買賣IC網 > PDF目錄16358 > ISL54100AHDMI-EVALZ (Intersil)EVAL BOARD FOR ISL54100AHDMI PDF資料下載
參數資料
| 型號： | ISL54100AHDMI-EVALZ |
| 廠商： | Intersil |
| 文件頁數： | 21/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR ISL54100AHDMI |
| 標準包裝： | 1 |
| 系列： | * |
9
FN6725.0
June 17, 2008
Register Listing
ADDRESS
REGISTER (DEFAULT VALUE)
BIT(S)
FUNCTION NAME
DESCRIPTION
0x00
Device ID (read only)
3:0
Device Revision
1 = initial silicon, 2 = second revision, etc.
7:4
Device ID
3 = ISL5410xA
0x01
Channel Activity Detect (read only)
0
Channel A Active
0: TMDS clock not present on Channel A
1: TMDS clock detected on Channel A
1
Channel B Active
0: TMDS clock not present on Channel B
1: TMDS clock detected on Channel B
2
Channel C Active
0: TMDS clock not present on Channel C
1: TMDS clock detected on Channel C
3
Channel D Active
0: TMDS clock not present on Channel D
1: TMDS clock detected on Channel D
0x02
Channel Selection (0x0C)
1:0
Channel Select
Selects the input channel for the mux. These 2 bits are Read
Only if Auto Channel Select is enabled.
0: Channel A selected
1: Channel B selected
2: Channel C selected
3: Channel D selected
2
Auto Channel Select 0: Manual Channel Select (using bits 0 and 1).
1: Auto Channel Select. Mux always selects the active
channel with the highest priority. A = 1st (highest), B = 2nd,
C = 3rd, D = 4th (lowest) priority.
An active channel is a channel that has clock activity on its
TMDS clock lines. If no channels are active, the A channel
is selected. (default)
3
Hardware Channel
Select
0: Software channel selection (using bits 0-2 of this register)
1: Hardware channel selection (using “Auto Channel Select”
and “CH Sel 0/1” external pins) (default)
4
Reset
Full chip reset. Write a 1 to reset. Will set itself to 0 when
reset is complete.
5
Power-down
0: Normal Operation
1: Puts the chip in a minimal power consumption mode,
turning off all TMDS outputs and open-circuiting all TMDS
inputs.
This bit is OR'ed with the Power-down input pin. If either is
set, the chip will enter power-down. Serial
I/O stays operational in PD mode.
Note: When exiting Power-down, a termination resistor
Recalibration cycle must be run to re-trim the termination
resistors (see register 0x03[7]).
ISL54100A, ISL54101A, ISL54102A
相關PDF資料 |
PDF描述 |
|---|---|
| ESA14DRSN-S288 | CONN EDGECARD 28POS .125 EXTEND |
| EMA14DRSN-S288 | CONN EDGECARD 28POS .125 EXTEND |
| ISL59119IBZ-EVALZ | EVAL BOARD FOR ISL59119IBZ |
| 2-1906014-3 | CA 2.0MM OFNR 50/125,LC SEC YEL |
| ESA14DRSD-S288 | CONN EDGECARD 28POS .125 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54100CQZ | 功能描述:IC REGENERATOR TMDS 4:1 128-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| ISL54100CQZ-EVAL | 制造商:Intersil Corporation 功能描述:ISL54100CQZ-EVAL EVALUATION BOARD - Bulk |
| ISL54100CQZ-EVALZ | 制造商:Intersil Corporation 功能描述:EVAL BD FOR ISL54100 TMDS REGENERATORS W/ MLTPLXRS - Bulk |
| ISL54100-EVM | 制造商:Intersil Corporation 功能描述:An Evaluation Board of Manual, automatic and infrared remote control,4:1 HDMI interface, and a CD of development files 制造商:Intersil Corporation 功能描述:An Evaluation Board of Manual, automatic and infrared remote control4:1 HDMI interface, and a CD of development files |
| ISL54100HDMI-EVALZ | 制造商:Intersil Corporation 功能描述:ISL54100HDMI EVALUATION BOARD, ROHS, 4HDMI IN, 1 HDMI OUT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。