- 您現在的位置：買賣IC網 > PDF目錄1928 > ISL54210IRTZ-T (Intersil)IC SWITCH DUAL SPDT HS 10-TDFN PDF資料下載
參數資料
| 型號： | ISL54210IRTZ-T |
| 廠商： | Intersil |
| 文件頁數： | 3/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DUAL SPDT HS 10-TDFN |
| 標準包裝： | 6,000 |
| 功能： | 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 35 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 3.6 V |
| 電流 - 電源： | 7µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN/MLP（3x3） |
| 包裝： | 帶卷 (TR) |
11
FN6661.2
March 18, 2010
Typical Application Block Diagram
Detailed Description
The ISL54210 device is a dual single pole/double throw
(SPDT) analog switch that operates from a single DC
power supply in the range of 2.7V to 3.6V. It was
designed to function as a dual 2-to-1 multiplexer to
select between USB differential data signals and audio L
and R stereo signals. It comes in tiny TQFN and TDFN
packages for use in MP3 players, PDAs, cellphones, and
other personal media players.
The part consists of two 2.5Ω audio switches and two
5.5Ω USB switches. The audio switches can accept
signals that swing below ground. They were designed to
pass audio left and right stereo signals, that are ground
referenced, with minimal distortion. The USB switches
were designed to pass high-speed USB differential data
signals with minimal edge and phase distortion.
The ISL54210 was specifically designed for MP3 players,
personal media players and cellphone applications that
need to combine the audio headphone jack and the USB
data connector into a single shared connector, thereby
saving space and component cost. A “Typical Application
Block Diagram” of this functionality is shown on page 11.
The ISL54210 incorporates circuitry for the detection of
the USB VBUS voltage, which is used to switch between
the audio CODEC drivers and USB transceiver of the MP3
player or cellphone. The ISL54210 contains a logic
control pin (CTRL) that when driven low while VBUS is
low, opens all switches and activates the audio click and
pop circuitry.
A detailed description of the two types of switches are
provided in the following sections. In a typical
application, the USB transmission and audio playback are
intended to be mutually exclusive operations.
Audio Switches
The two audio switches (L, R) are 2.5Ω switches that can
pass signals that swing below ground. Crosstalk between
the audio switches is <-100dB over the audio band.
These switches have excellent off-isolation >105dB over
the audio band with a 32Ω load.
Over a signal range of ±1V (0.707VRMS) with
VDD > 2.7V, these switches have an extremely low rON
resistance variation. They can pass ground referenced
audio signals with very low distortion (<0.06% THD+N)
when delivering 15.6mW into a 32Ω headphone speaker
Performance Curves” beginning on page 14.
The audio drivers should be connected at the L and R
side of the switch (pins 5 and 6 for TQFN, pins 6 and 7
for TDFN) and the speaker loads should be connected at
the COM side of the switch (pins 2 and 3 for TQFN, pins
3 and 4 for TDFN).
The audio switches have click and pop circuitry on the L
and R side that is activated when the VBUS voltage is ≤
VDD + 0.2V or floating and the CTRL voltage ≤ to 0.5V or
floating. The ISL54210 should be put in this mode before
powering down or powering up of the audio CODEC
drivers. In this mode, both the audio and USB in-line
switches will be OFF and the audio click and pop circuitry
will be ON. The high off-isolation of the audio switches
along with the click and pop circuitry will isolate the
transients generated during power-up and power-down
of the audio CODECs from getting through to the
headphones, thus eliminating click and pop noise in the
headphones.
The audio switches are active (turned ON) whenever the
VBUS voltage is ≤ VDD + 0.2V or floating and the CTRL
voltage ≥ to 1.4V.
ISL54210
USB
TRANSCEIVER
HIGH-SPEED
AUDIO
COM -
COM +
VBUS
GND
D-
D+
L
R
VDD
CTRL
LOGIC CONTROL
CONTROLLER
4M
Ω
4M
Ω
CODEC
CLICK
AND
POP
VBUS
3.3V
200k
Ω
200k
Ω
USB/HEADPHONE
JACK
ISL54210
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54211IRTZ-T | IC SWITCH DUAL SPDT HS 10-TDFN |
| ISL54212IRTZ-T | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54213IRTZ-T | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54214IRUZ-T | IC USB SWITCH DUAL SP3T 12UTQFN |
| ISL54215IRUZ-T | IC USB SWITCH DUAL SPDT 10UTQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54210IRUZ-T | 功能描述:IC SWITCH HS DUAL SPDT 10-TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:2,500 系列:- 功能:視頻交叉點開關 電路:1 x 8:6 導通狀態電阻:- 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3.135 V ~ 5.25 V 電流 - 電源:55mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1214 (CN2011-ZH PDF) 其它名稱:FMS6502MTC24XTR |
| ISL54211 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:MP3/USB 2.0 High Speed Switch with Negative Signal Handling/Click and Pop Suppression |
| ISL54211EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL54211 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL54211IRTZ | 功能描述:IC SWITCH DUAL SPDT HS 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| ISL54211IRTZ-T | 功能描述:IC SWITCH DUAL SPDT HS 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。