- 您現在的位置：買賣IC網 > PDF目錄8577 > ISL59446IRZ-T7 (Intersil)IC AMP MUX 4:1 500MHZ 32-QFN PDF資料下載
參數資料
| 型號： | ISL59446IRZ-T7 |
| 廠商： | Intersil |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP MUX 4:1 500MHZ 32-QFN |
| 標準包裝： | 1 |
| 應用： | 4:1 多路復用器-放大器 |
| 電路數： | 3 |
| -3db帶寬： | 620MHz |
| 轉換速率： | 1600 V/µs |
| 電流 - 電源： | 44mA |
| 電流 - 輸出 / 通道： | 135mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x6） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1235 (CN2011-ZH PDF) |
| 其它名稱： | ISL59446IRZ-T7DKR |
10
FN6261.2
June 5, 2012
AC Test Circuits
testing AC performance at 500
Ω and 150Ω loads.
Figure 28E illustrates the optimum output load for 50
Ω and
75
Ω cable-driving.
Application Information
General
Key features of the ISL59446 include a fixed gain of 2,
buffered high impedance analog inputs and excellent AC
performance at output loads down to 150
Ω for video
cable-driving. The current feedback output amplifiers are
stable operating into capacitive loads.
For the best isolation and crosstalk rejection, all GND pins
and NIC pins must connect to the GND plane.
AC Design Considerations
High speed current-feed amplifiers are sensitive to
capacitance at the inverting input and output terminals. The
ISL59446 has an internally set gain of 2, so the inverting
input is not accessible. Capacitance at the output terminal
increases gain peaking (Figure 1) and pulse overshoot
optimized for a total output capacitance of up to 2.1pF over
the load range of 150
Ω to 500Ω. When PCB trace
capacitance and component capacitance exceed 2pF, pulse
overshoot becomes strongly dependent on the input pulse
amplitude and slew rate. This effect is shown in Figures 19
and 20, which show approximate pulse overshoot as a
function of input slew rate and output capacitance. Fast
pulse rise and fall times (<150ns) at input amplitudes above
0.2V, cause the input pulse slew rate to exceed the
1600V/s output slew rate of the ISL59446. At 125ps rise
time, pulse input amplitudes >0.2V cause slew rate limit
operation. Increasing levels of output capacitance reduce
stability resulting in increased overshoot, and settling time.
PC board trace length should be kept to a minimum in order
to minimize output capacitance and prevent the need for
controlled impedance lines. At 500MHz trace lengths
approaching 1” begin exhibiting transmission line behavior
and may cause excessive ringing if controlled impedance
traces are not used. Figure 28A shows the optimum
inter-stage circuit when the total output trace length is less
than the critical length of the highest signal frequency.
For applications where pulse response is critical and where
inter-stage distances exceed LCRIT, the circuit shown in
capacitance seen by the amplifier output to the trace
capacitance from the output pin to the resistor. Therefore,
RS should be placed as close to the ISL59446 output pin as
possible. For inter-stage distances much greater than LCRIT,
the back-loaded circuit shown in Figure 28E should be used
with controlled impedance PCB lines, with RS and RL equal
to the controlled impedance.
For applications where inter-stage distances are long, but
pulse response is not critical, capacitor CS can be added to
low values of RS to form a low-pass filter to dampen pulse
overshoot. This approach avoids the need for the large gain
correction required by the -6dB attenuation of the
AC Test Circuits
FIGURE 28A. TEST CIRCUIT WITH OPTIMAL OUTPUT LOAD
FIGURE 28B. INTER-STAGE APPLICATION CIRCUIT
FIGURE 28C. 500
Ω TEST CIRCUIT WITH 50Ω LOAD
FIGURE 28D. 150Ω TEST CIRCUIT WITH 50
Ω LOAD
FIGURE 28E. BACKLOADED TEST CIRCUIT FOR 75
Ω VIDEO
CABLE APPLICATION
ISL59446
*CL
50
Ω
VIN
500
Ω, or
RL
1.1pF
or
75
Ω
150
Ω
*CL Includes PCB trace capacitance
VOUT
LCRIT
x2
ISL59446
CS
50
Ω
VIN
500
Ω, or
RL
or
75
Ω
75
Ω
LCRIT
RS
CL
x2
ISL59446
RS
*CL
VIN
475
Ω
TEST
1.1pF
50
Ω
56.2
Ω
50
Ω
EQUIPMENT
*CL Includes PCB trace capacitance
LCRIT
x2
ISL59446
RS
*CL
VIN
118
Ω
TEST
2.1pF
50
Ω,or
86.6
Ω
50
Ω
EQUIPMENT
75
Ω
*CL Includes PCB trace capacitance
LCRIT
x2
ISL59446
RS
*CL
VIN
50
Ω or 75Ω
TEST
2.1pF
50
Ω
or
75
Ω
50
Ω or 75Ω
EQUIPMENT
*CL Includes PCB trace capacitance
LCRIT
x2
ISL59446
相關PDF資料 |
PDF描述 |
|---|---|
| EL4543IUZ | IC DVR TRPL DIFF TW-PAIR 24-QSOP |
| HA5023IBZ | IC OPAMP DUAL 125MHZ VIDEO 8SOIC |
| AD7534JPZ-REEL | IC DAC 14BIT MULT W/BUFF 20PLCC |
| ISL59837IAZ | IC VIDEO DRIVER TRUE SGL 16-QSOP |
| LTC1596-1ACN | IC D/A CONV 16BIT MLTPLYNG 16DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59448 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500MHz Triple 2:1 Gain-of-2, Multiplexing Amplifier |
| ISL59448EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL59448 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL59448IAZ | 功能描述:IC AMP TRIPLE MUX 500MHZ 24-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59448IAZ-T7 | 功能描述:IC AMP MUX 2:1 500MHZ 24-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59450 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multiformat Video Crosspoint with Integrated Sync Separator |
發布緊急采購，3分鐘左右您將得到回復。