2
FN6261.2
June 5, 2012
Absolute Maximum Ratings (T
A = +25°C)
Thermal Information
Supply Voltage (V+ to V-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.5V, V+ +0.5V
Supply Turn-on Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/s
Digital & Analog Input Current (Note
4) . . . . . . . . . . . . . . . . . . 50mA
Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7). . . .2500V
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V
Thermal Resistance (Typical, Note
5, 6)θJA (°C/W) θJC (°C/W)
32 Ld QFN Package . . . . . . . . . . . . . .
43
10
Storage Temperature Range . . . . . . . . . . . . . . . . . . -65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . . -40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . -40°C to +125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .See Curves
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . .see link below
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
4. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values.
5.
θ
JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
6. For
θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
V+ = +5V, V- = -5V, GND = 0V, TA = +25°C, VOUT = ±2VP-P and RL = 500Ω to GND, CL = 0pF, unless otherwise
specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
GENERAL
+IS Enabled
Enabled Supply Current
No load, VIN = 0V, Enable Low
40
44
48
mA
-IS Enabled
Enabled Supply Current
No load, VIN = 0V, Enable Low
-45
-41
-37
mA
+IS Disabled
Disabled Supply Current
No load, VIN = 0V, Enable High
3
3.4
3.8
mA
-IS Disabled
Disabled Supply Current
No load, VIN = 0V, Enable High
-40
-6
A
VOUT
Positive and Negative Output Swing
VIN = ±2.5V; RL = 500Ω
±3.8
±4.0
±4.2
V
IOUT
Output Current
VIN = 0.825V RL = 10Ω
±80
±135
±180
mA
VOS
Output Offset Voltage
-40
0
+40
mV
Ib
Input Bias Current
VIN = 0V
-4
-2
-1
A
ROUT
HIZ Output Resistance
HIZ = Logic High
700
900
1150
Ω
ROUT
Enabled Output Resistance
HIZ = Logic Low
0.2
Ω
RIN
Input Resistance
VIN = ±1.75V
10
M
Ω
ACL or AV
Voltage Gain
RL = 500Ω
1.94
1.99
2.04
V/V
LOGIC
VIH
Input High Voltage (Logic Inputs)
2V
VIL
Input Low Voltage (Logic Inputs)
0.8
V
IIH
Input High Current (Logic Inputs)
VH = 5V
200
260
320
A
IIL
Input Low Current (Logic Inputs)
VL = 0V
-4
-2
-1
A
AC GENERAL
PSRR
Power Supply Rejection Ratio
DC, PSRR V+ and V- combined
VOUT = 0dBm
45
53
dB
Xtalk
Channel to Channel Crosstalk
f = 10MHz, ChX-Ch Y-Talk
VIN = 1VP-P; CL = 1.1pF
74
dB
ISL59446