FN7510.0 February 14, 2008 Sync Separator HSYNC Timing for 720p ISL59450 Serial Communications I
參數資料
型號: ISL59450IQZ
廠商: Intersil
文件頁數: 27/37頁
文件大?。?/td> 0K
描述: IC SWITCH VID CRSSPNT 128-MQFP
標準包裝: 66
系列: *
33
FN7510.0
February 14, 2008
Sync Separator HSYNC Timing for 720p
ISL59450 Serial Communications
I2C Overview
The ISL59450 uses a 2-wire I2C serial bus for
communication with its host. SCL is the Serial Clock line,
driven by the host, and SDA is the Serial Data line, which
can be driven by all devices on the bus. SDA is open drain to
allow multiple devices to share the same bus
simultaneously.
Communication is accomplished in three steps:
1. The Host selects the ISL59450 with which it wishes to
communicate.
2. The Host writes the initial ISL59450 Configuration
Register address it wishes to write to or read from.
3. The Host writes to or reads from the ISL59450’s
Configuration Register. The ISL59450’s internal address
pointer auto increments, so to read registers 0x00
through 0x16, for example, one would write 0x00 in step
two, then repeat step four 28 times, with each read
returning the next register value.
The ISL59450 has a 7-bit address on the serial bus. The upper
6-bits are permanently set to 100010x, with the x determined by
the state of the Address pin (Table 3). This allows two
ISL59450s to be independently controlled while sharing the
same bus. The Address pin has an internal pull-down resistor
to pull the terminal low to set a zero.
The bus is nominally inactive, with SDA and SCL high.
Communication begins when the host issues a START
command by taking SDA low while SCL is high (Figure 34).
The ISL59450 continuously monitors the SDA and SCL lines
for the start condition and will not respond to any command
until this condition has been met. The host then transmits the
7-bit serial address plus a R/W bit, indicating if the next
transaction will be a Read (R/W = 1) or a Write (R/W = 0). If
the address transmitted matches that of any device on the
bus, that device must respond with an ACKNOWLEDGE
PARAMETER
DESCRIPTION
CONDITIONS
TYP
UNIT
tdHOUT
HOUT Timing Relative to Input
200
ns
tHOUT
Horizontal Output Width
5s
CONDITIONS: VD = 3.3V TA = +25°C
SYNCIN
tdHOUT
tHOUT
HOUT
PARAMETER
DESCRIPTION
CONDITIONS
TYP
@ 3.3V
UNIT
tdHOUT
HOUT Timing Relative to Input
90
ns
tHOUT
Horizontal Output Width
1.90
s
TABLE 3. I2C ADDRESS OPTIONS
B7
B6
B5
B4
B3
B2
B1
B0
HEX
A6
(MSB)
A5A4
A3A2
A1
A0
(Address) R/W
1
0
1
0
1/0 0x85/0x84
1
0
1
1/0 0x87/0x86
ISL59450
相關PDF資料
PDF描述
ISL59530IRZ IC VIDEO CROSSPOINT SWITCH 72QFN
ISL59532IKEZ IC CROSSPOINT SW 32X32 356BGA
ISL59534IKEZ IC CROSSPOINT SW 32X16 356BGA
ISL6436LIB IC CTRLR PS USB DUAL PORT 8-SOIC
ISL76120ARTZ-T IC MULTIPLEXER DUAL SPDT 10TDFN
相關代理商/技術參數
參數描述
ISL59450IQZ-EVAL 制造商:Intersil Corporation 功能描述:ISL59450IQZ-EVAL EVALUATION BOARD - Bulk
ISL59451 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 4:1 DC Restored Single Supply Video Multiplexing Amplifier
ISL59451IRZ 功能描述:IC AMP TRIPLE MUX 250MHZ 32-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板:VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源,單路/雙路(±):9 V ~ 20 V,±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬)裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件
ISL59451IRZ-T7 功能描述:IC AMP MUX TRIPLE 4:1 DC 32-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板:VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源,單路/雙路(±):9 V ~ 20 V,±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬)裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件
ISL59452 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 4:1 Single Supply Video Multiplexing Amplifier