- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1160 (NXP Semiconductors N.V.) Embedded Universal Serial Bus Host Controller PDF資料下載
參數資料
| 型號： | ISP1160 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Embedded Universal Serial Bus Host Controller |
| 中文描述： | 嵌入式通用串行總線主控制器 |
| 文件頁數： | 55/88頁 |
| 文件大?。?/td> | 2044K |
| 代理商： | ISP1160 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
Philips Semiconductors
ISP1160
Embedded USB Host Controller
Product data
Rev. 04 — 04 July 2003
55 of 88
9397 750 11371
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
8
PPS
On read—
PortPowerStatus:
This bit reflects the port power
status, regardless of the type of power switching implemented.
This bit is cleared if an overcurrent condition is detected.
The HCD sets this bit by writing SetPortPower or SetGlobalPower.
The HCD clears this bit by writing ClearPortPower or
ClearGlobalPower. Which power control switches are enabled is
determined by PowerSwitchingMode.
In the global switching mode (PowerSwitchingMode
=
0), only
Set/ClearGlobalPower controls this bit. In per-port power switching
(PowerSwitchingMode
=
1), if bit PortPowerControlMask[NDP] for
the port is set, only Set/ClearPortPower commands are enabled. If
the mask is not set, only Set/ClearGlobalPower commands are
enabled.
When port power is disabled, CurrentConnectStatus,
PortEnableStatus, PortSuspendStatus, and PortResetStatus
should be reset.
0 —
port power is off
1 —
port power is on
On write—
SetPortPower:
The HCD writes a logic 1 to set
bit PortPowerStatus. Writing a logic 0 has no effect.
Remark:
This bit always reads logic 1 if power switching is not
supported.
reserved
On read—
PortResetStatus:
When this bit is set by a write to
SetPortReset, port reset signaling is asserted. When reset is
completed, this bit is cleared when PortResetStatusChange is set.
This bit cannot be set if CurrentConnectStatus is cleared.
7 to 5
4
-
PRS
0 —
port reset signal is not active
1 —
port reset signal is active
On write—
SetPortReset:
The HCD sets the port reset signaling
by writing a logic 1 to this bit. Writing a logic 0 has no effect. If
CurrentConnectStatus is cleared, this write does not set
PortResetStatus but instead sets ConnectStatusChange. This
informs the driver that it attempted to reset a disconnected port.
On read—
PortOverCurrentIndicator:
This bit is valid only when
the Root Hub is configured in such a way that overcurrent
conditions are reported on a per-port basis. If per-port overcurrent
reporting is not supported, this bit is set to logic 0. If cleared, all
power operations are normal for this port. If set, an overcurrent
condition exists on this port. This bit always reflects the overcurrent
input signal.
3
POCI
0 —
no overcurrent condition
1 —
overcurrent condition detected
(write)
ClearSuspendStatus:
The HCD writes a logic 1 to initiate
a resume. Writing a logic 0 has no effect. A resume is initiated only
if PortSuspendStatus is set.
Table 35:
Bit
HcRshPortStatus[1:2] register: bit description
…continued
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1160BD | Embedded Universal Serial Bus Host Controller |
| ISP1160BM | Embedded Universal Serial Bus Host Controller |
| ISP1161A | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161ABD | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161ABM | Full-speed Universal Serial Bus single-chip host and device controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1160BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD,157 | 功能描述:USB 接口集成電路 USB 1.1 HOST CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1160BD/01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD/01,118 | 功能描述:USB 接口集成電路 USB HOST CTRL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1160BD/01,151 | 功能描述:USB 接口集成電路 USB FULL SPEED HOST RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發(fā)布緊急采購，3分鐘左右您將得到回復。