- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1362BD (NXP SEMICONDUCTORS) Single-chip Universal Serial Bus On-The-Go controller PDF資料下載
參數資料
| 型號： | ISP1362BD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Single-chip Universal Serial Bus On-The-Go controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 30/150頁 |
| 文件大?。?/td> | 647K |
| 代理商： | ISP1362BD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
30 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
DcInterruptEnable
DcInterrupt.
The DcMode register (bit 3) is the overall DC interrupt enable.
DcHardwareCon
fi
guration determines the following features:
Level-triggered or edge-triggered (bit 1)
Output polarity (bit 0).
For details on the interrupt logic in the DC, refer to the
Interrupt Control
application
note.
9.7.3
Combining INT1 and INT2
In some embedded systems, interrupt inputs to the CPU are a very scarce resource.
The system designer might want to use just one interrupt line to serve the HC, the DC
and the OTG controller. In such a case, make sure the OneINT feature is activated.
When OneINT (bit 9 of the HcHardwareCon
fi
guration register) is set to logic 1, both
the INT1 (HC or OTG controller) interrupt and the INT2 (DC) interrupt are routed to
pin INT1, thereby reducing hardware resource requirements.
Remark:
Both the host controller (or OTG controller) and the device controller
interrupts must be set to the same polarity (active HIGH or active LOW) and the same
trigger type (edge or level). Failure to conform to this will lead to unpredictable
behavior of the ISP1362.
9.7.4
Behavior difference between level-triggered and edge-triggered interrupts
In many microprocessor systems, the operating system disables an interrupt when it
is in an Interrupt Service Routine (ISR). If there is an interrupt event during this
period, it will lead to:
Level-triggered interrupt:
When the ISP1362 interrupt asserts, the operating
system takes no action because it disables the interrupt when it is in the ISR. The
interrupt line of the ISP1362 remains asserted. When the operating system exits the
ISR and re-enables the interrupt processing, it sees the asserted interrupt line and
immediately enters the ISR.
Edge-triggered interrupt:
When the ISP1362 outputs a pulse, the operating system
takes no action because it disables the interrupt when it is in the ISR. The interrupt
line of the ISP1362 goes back to the inactive state. When the operating system exits
the ISR and re-enables the interrupt processing, it sees no pending interrupt. As a
result, the interrupt is missed.
If the system needs to know whether an interrupt (approximately 160 ns pulse width)
occurs during this period, it may read the Hc
μ
PInterrupt register (see
Table 68
).
10. Power-on reset (POR)
When V
CC
is directly connected to the RESET pin, the internal POR pulse width
(t
PORP
) will be typically 800 ns. The pulse is started when V
CC
rises above V
trip
(2.03 V).
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1362EE | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1501 | Hi-Speed Universal Serial Bus peripheral transceiver |
| ISP1520 | Hi-Speed Universal Serial Bus hub controller |
| ISP1520BD | Hi-Speed Universal Serial Bus hub controller |
| ISP1521 | Hi-Speed Universal Serial Bus hub controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1362BD,118 | 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1362BD,151 | 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1362BD,157 | 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1362BD157 | 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB-OTG 64LQFP 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 64-LQFP |
| ISP1362BDFA | 功能描述:IC USB OTG CONTROLLER 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。