參數資料
型號： ISP1583BS,551
廠商： ST-ERICSSON
元件分類： 總線控制器
英文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQCC64
封裝： 9 X 9 MM, 0.85 MM HEIGHT, LEAD FREE, PLASTIC, MO-220, SOT-804-1, HVQFN-64
文件頁數： 37/100頁
文件大小： 508K
代理商： ISP1583BS,551
ISP1583_7
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 07 — 22 September 2008
40 of 99
NXP Semiconductors
ISP1583
Hi-Speed USB peripheral controller
9.3.3 Data Port register (address: 20h)
This 2-byte register provides direct access for a microcontroller to the FIFO of the indexed
endpoint. The bit allocation is shown in Table 39.
Peripheral-to-host (IN endpoint): After each write action, an internal counter is auto
incremented (by two for a 16-bit access, by one for an 8-bit access) to the next location in
the TX FIFO. When all bytes are written (FIFO byte count = endpoint MaxPacketSize), the
Table 38.
Control Function register: bit description
Bit
Symbol
Description
7 to 5 -
reserved.
4
CLBUF
Clear Buffer: Logic 1 clears the TX or RX buffer of the indexed endpoint. The
RX buffer is automatically cleared once the endpoint is completely read. This bit
is set only when it is necessary to forcefully clear the buffer.
Remark: If using double buffer, to clear both the buffers issue the CLBUF
command two times. For details on clearing buffers, refer to Ref. 5 “ISP1582/83
3
VENDP
Validate Endpoint: Logic 1 validates data in the TX FIFO of an IN endpoint to
send on the next IN token. In general, the endpoint is automatically validated
when its FIFO byte count has reached endpoint MaxPacketSize. This bit is set
only when it is necessary to validate the endpoint with the FIFO byte count,
which is below endpoint MaxPacketSize.
Remark: Use either bit VENDP or register Buffer Length to validate endpoint
FIFO with FIFO bytes.
2
DSEN
Data Stage Enable: This bit controls the response of the ISP1583 to a control
transfer. After the completion of the set-up stage, rmware must determine
whether a data stage is required. For control OUT, rmware will set this bit and
the ISP1583 goes into the data stage. Otherwise, the ISP1583 will NAK the data
stage transfer. For control IN, rmware will set this bit before writing data to the
TX FIFO and validate the endpoint. If no data stage is required, rmware can
immediately set the STATUS bit after the set-up stage.
Remark: The DSEN bit is cleared once the OUT token is acknowledged by the
device and the IN token is acknowledged by the PC host. This bit cannot be
read back and reading this bit will return logic 0.
1
STATUS
Status Acknowledge: Only applicable for control IN or OUT.
This bit controls the generation of ACK or NAK during the status stage of a
SETUP transfer. It is automatically cleared when the status stage is completed,
or when a SETUP token is received. No interrupt signal will be generated.
0 — Sends NAK
1 — Sends an empty packet following the IN token (peripheral-to-host) or ACK
following the OUT token (host-to-peripheral)
Remark: The STATUS bit is cleared to zero once the zero-length packet is
acknowledged by the device or the PC host.
Remark: Data transfers preceding the status stage must rst be fully completed
before the STATUS bit can be set.
0
STALL
Stall Endpoint: Logic 1 stalls the indexed endpoint. This bit is not applicable for
isochronous transfers.
Remark: Stalling a data endpoint will confuse the Data Toggle bit about the
stalled endpoint because the internal logic picks up from where it is stalled.
Therefore, the Data Toggle bit must be reset by disabling and re-enabling the
corresponding endpoint (by setting bit ENABLE to logic 0, followed by logic 1 in
the Endpoint Type register) to reset the PID.
相關PDF資料
PDF描述
ISP1583ET2 UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
ISP1761ET,518 UNIVERSAL SERIAL BUS CONTROLLER, PBGA128
ISP1761BE,518 UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
ISP1761BE,551 UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
ISP1761BE,518 UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
相關代理商/技術參數
參數描述
ISP1583BSGA 功能描述:IC USB CTRL HI-SPEED 64HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
ISP1583BS-S 功能描述:USB 接口集成電路 HI-SPEED USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1583BS-T 功能描述:USB 接口集成電路 USB PERIPH CNTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1583BSUM 功能描述:IC USB PERIPH CONTROLLER 64HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
ISP1583ET 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hi-Speed USB peripheral controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*