- 您現在的位置：買賣IC網 > PDF目錄373087 > K9F5608U0 (SAMSUNG SEMICONDUCTOR CO. LTD.) TV 6C 6#12 PIN WALL RECP PDF資料下載
參數資料
| 型號： | K9F5608U0 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | TV 6C 6#12 PIN WALL RECP |
| 中文描述： | 32M的× 8位NAND閃存 |
| 文件頁數： | 23/29頁 |
| 文件大?。?/td> | 610K |
| 代理商： | K9F5608U0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁
K9F5608U0A-YCB0,K9F5608U0A-YIB0
FLASH MEMORY
23
Figure 6. Sequential Row Read2 Operation (GND Input=Fixed Low)
PAGE PROGRAM
The device is programmed basically on a page basis, but it does allow multiple partial page programing of a byte or consecutive
bytes up to 528, in a single page program cycle. The number of consecutive partial page programming operation within the same
page without an intervening erase operation should not exceed 2 for main array and 3 for spare array. The addressing may be done
in any random order in a block. A page program cycle consists of a serial data loading period in which up to 528 bytes of data may be
loaded into the page register, followed by a non-volatile programming period where the loaded data is programmed into the appropri-
ate cell. Serial data loading can be started from 2nd half array by moving pointer. About the pointer operation, please refer to the
attached technical notes.
The serial data loading period begins by inputting the Serial Data Input command(80h), followed by the three cycle address input and
then serial data loading. The bytes other than those to be programmed do not need to be loaded.The Page Program confirm com-
mand(10h) initiates the programming process. Writing 10h alone without previously entering the serial data will not initiate the pro-
gramming process. The internal write controller automatically executes the algorithms and timings necessary for program and verify,
thereby freeing the system controller for other tasks. Once the program process starts, the Read Status Register command may be
entered, with RE and CE low, to read the status register. The system controller can detect the completion of a program cycle by
monitoring the R/B output, or the Status bit(I/O 6) of the Status Register. Only the Read Status command and Reset command are
valid while programming is in progress. When the Page Program is complete, the Write Status Bit(I/O 0) may be checked(Figure 7).
The internal write verify detects only errors for "1"s that are not successfully programmed to "0"s. The command register remains in
Read Status command mode until another valid command is written to the command register.
50h
A
0
~ A
3
& A
9
~ A
24
I/O
0
~
7
R/B
Start Add.(3Cycle)
Data Output
Data Output
Data Output
2nd
Nth
(16Byte)
(16Byte)
Data Field
Spare Field
1st
Block
Nth
(A
4
~ A
7
:
Don
t Care)
1st
Figure 7. Program Operation
80h
A
0
~ A
7
& A
9
~ A
24
528 Byte Data
I/O
0
~
7
R/B
Address & Data Input
I/O
0
Pass
10h
70h
Fail
t
R
t
R
t
R
t
PROG
≈
相關PDF資料 |
PDF描述 |
|---|---|
| K9F5608U0A | TV 6C 6#12 PIN RECP |
| K9F5608U0A-YCB0 | TV 16C 16#16 PIN RECP |
| K9F5608U0A-YIB0 | TV 79C 79#22D PIN RECP |
| K9F6408U0C-T | 8M x 8 Bit NAND Flash Memory |
| K9F6408U0C-V | 8M x 8 Bit NAND Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K9F5608U0A | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit NAND Flash Memory |
| K9F5608U0A-YCB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit NAND Flash Memory |
| K9F5608U0A-YIB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit NAND Flash Memory |
| K9F5608U0B | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit , 16M x 16 Bit NAND Flash Memory |
| K9F5608U0B-DCB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit , 16M x 16 Bit NAND Flash Memory |
發(fā)布緊急采購，3分鐘左右您將得到回復。