- 您現在的位置：買賣IC網 > PDF目錄1931 > KS8721BLI TR (Micrel Inc)TXRX 10/100 3.3V 48-LQFP PDF資料下載
參數資料
| 型號： | KS8721BLI TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 4/35頁 |
| 文件大小： | 0K |
| 描述： | TXRX 10/100 3.3V 48-LQFP |
| 標準包裝： | 1,000 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | MII，RMII |
| 電源電壓： | 2.375 V ~ 2.625 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 配用： | 576-1007-ND - BOARD EVAL EXPERIMENT KS8721BL |
| 其它名稱： | KS8721BLITR KS8721BLITR-ND |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Micrel, Inc.
KS8721BL/SL
June 2009
12
M9999-062509-1.3
SQE and Jabber Function (10BASE-T only)
In 10BASE-T operation, a short pulse is put out on the COL pin after each packet is transmitted. This is required as a
test of the 10BASE-T transmit/receive path and is called an SQE test. The 10BASE-T transmitter is disabled and COL
goes high if TXEN is high for more than 20ms (Jabbering). If TXEN then goes low for more than 250ms, the 10BASE-T
transmitter is re-enabled and COL goes low.
Auto-Negotiation
The KS8721BL/SL performs auto-negotiation by hardware strapping option (pin 29) or software (Register 0.12). It
automatically chooses its mode of operation by advertising its abilities and comparing them with those received from its
link partner whenever auto-negotiation is enabled. It can also be congured to advertise 100BASE-TX or 10BASE-T in
either full- or half-duplex mode (please refer to “Auto-Negotiation”). Auto-negotiation is disabled in the FX mode.
During auto-negotiation, the contents of Register 4, coded in fast link pulse (FLP), are sent to its link partner under the
conditions of power-on, link-loss, or restart. At the same time, the KS8721BL/SL monitors incoming data to determine
its mode of operation. The parallel detection circuit is enabled as soon as either 10BASE-T normal link pulse (NLP) or
100BASE-TX idle is detected. The operation mode is congured based on the following priority:
Priority 1: 100BASE-TX, full-duplex
Priority 2: 100BASE-TX, half-duplex
Priority 3: 10BASE-T, full-duplex
Priority 4: 10BASE-T, half-duplex
When the KS8721BL/SL receives a burst of FLP from its link partner with three identical link code words (ignoring
acknowledge bit), it will store these code words in Register 5 and wait for the next three identical code words. Once the
KS8721BL/SL detects the second code words, it then congures itself according to the above-mentioned priority. In
addition, the KS8721BL/SL also checks for 100BASE-TX idle or 10BASE-T NLP symbols. If either is detected, the
KS8721BL/SL automatically congures to match the detected operating speed.
MII Management Interface
The KS8721BL/SL supports the IEEE 802.3 MII Management Interface, also known as the Management Data
Input/Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the
KS8721BL/SL. The MDIO interface consists of the following:
A physical connection including a data line (MDIO), a clock line (MDC), and an optional interrupt line (INTRPT).
A specic protocol that runs across the above-mentioned physical connection that allows one controller to
communicate with multiple KS8721BL/SL devices. Each KS8721BL/SL is assigned an MII address between 0
and 31 by the PHYAD inputs.
An internal addressable set of fourteen 16-bit MDIO registers. Registers [0:6] are required and their functions
are specied by the IEEE 802.3 specications. Additional registers are provided for expanded functionality.
The INTPRT pin functions as a management data interrupt in the MII. An active Low or High in this pin indicates a
status change on the KS8721BL/SL based on 1fh.9 level control. Register bits at 1bh[15:8] are the interrupt enable bits.
Register bits at 1bh[7:0] are the interrupt condition bits. This interrupt is cleared by reading Register 1bh.
MII Data Interface
The data interface consists of separate channels for transmitting data from a 10/100 802.3 compliant Media Access
Controller (MAC) to the KS8721BL/SL, and for receiving data from the line. Normal data transmission is implemented in
4B nibble mode (4-bit wide nibbles).
Transmit Clock (TXC)
The transmit clock is normally generated by the KS8721BL/SL from an external 25MHz reference source at the X1
input. The transmit data and control signals must always be synchronized to the TXC by the MAC. The KS8721BL/SL
normally samples these signals on the rising edge of the TXC.
Receive Clock (RXC)
For 100BASE-TX links, the receive clock is continuously recovered from the line. If the link goes down, and auto-
negotiation is disabled, the receive clock operates off the master input clock (X1 or TXC). For 10BASE-T links, the
相關PDF資料 |
PDF描述 |
|---|---|
| KS8721SL | TXRX 10/100 3.3V 48-SSOP |
| KS8842-32MQL | IC SWITCH 10/100 32BIT 128PQFP |
| KS8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KS8993I | IC SWITCH 10/100 3PORT 128PQFP |
| KS8993ML | IC SWITCH 10/100 3PORT 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KS8721BMCEVAL | 制造商:Micrel 功能描述:Evaluation Kit For 2.5V 10/100 Base TX/FX MII Physical Layer Transceiver |
| KS8721BMC-EVAL | 功能描述:BOARD EVAL EXPERIMENT KS8721BMC RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| KS8721BT | 功能描述:IC TXRX PHY 10/100 TX/FX 48TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KS8721BT-EVAL | 功能描述:BOARD EVAL EXPERIMENT KS8721BT RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| KS8721CL | 功能描述:TXRX 10/100 3.3V 48-LQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
發布緊急采購，3分鐘左右您將得到回復。