參數資料
型號: KSZ8001L-EVAL
廠商: Micrel Inc
文件頁數: 15/46頁
文件大小: 0K
描述: BOARD EVALUATION FOR KSZ8001L
標準包裝: 1
主要目的: 接口,以太網 PHY
嵌入式:
已用 IC / 零件: KSZ8001L
主要屬性: 單芯片 PHY,100BASE-TX/100BASE-FX/10BASE-T
次要屬性: MII,RMII,SMII,HP 自動 MDI,MDI-X 自動極性校正,LinkMD
已供物品:
相關產品: KSZ8001SA3-ND - TXRX 10/100 LINKMD 3.3V 48-SSOP
KSZ8001LIA3-ND - TXRX 10/100 LINKMD 3.3V 48-LQFP
KSZ8001LA3TR-ND - TXRX 10/100 LINKMD 3.3V 48-LQFP
KSZ8001LA3-ND - TXRX 10/100 LINKMD 3.3V 48-LQFP
KSZ8001LA2TR-ND - TXRX 10/100 LINKMD 3.3V 48-LQFP
KSZ8001LA2-ND - TXRX 10/100 LINKMD 3.3V 48-LQFP
KSZ8001SL TR-ND - TXRX 10/100 LINKMD 3.3V 48-SSOP
576-2110-ND - TXRX 10/100 LINKMD 3.3V 48-SSOP
KSZ8001SI-ND - TXRX 10/100 LINKMD 3.3V 48-SSOP
KSZ8001S TR-ND - TXRX 10/100 LINKMD 3.3V 48-SSOP
更多...
其它名稱: 576-1620
Micrel
KSZ8001
June 2009
Revision 1.04
22
Auto MDI/MDI-X Cross-Over Transformer Connection
KSZ8001 features HP Auto MDI/MDI-X crossover and requires symmetric transformers that support Auto MDI/MDI-X.
See
“Selection of Isolation Transformer” for a list of transformers that support Auto MDI/MDI-X.
Power Management
The KSZ8001 offers the following modes for power management:
Power Down Mode:
This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# Low. In the power down
state, the KS8061 disables all internal functions and drives output pins to logic zero, except for the MII serial management
interface.
Power Saving Mode:
writing to register 1fh.10 can disable this mode. The KSZ8001 will then turn off everything except for
the Energy Detect and PLL circuits when the cable is not installed. In other words, the KSZ8001 will shutdown most of the
internal circuits to save power if there is no link. Power Saving mode will be in this most effective state when Auto-
Negotiation Mode is enabled.
100BASE-FX Mode
100BASE-FX mode is activated when FXSD/FXEN is higher than 0.6V (This pin has a default pull down). Under this mode, the auto-
negotiation and auto-MDIX features are disabled.
In fiber operation FXSD pin should connect to the SD (signal detect) output of the fiber module. The internal threshold of FXSD is
around
Vdd +/- 50 mV (2.2V +/- 0.05V at 3.3V). Above this level, it is considered Fiber signal detected, and the operation is
summarized in the following table:
FXSD/FXEN
Condition
Less than 0.6V
100TX mode
Less than 2.15V,
but greater than 0.6V
FX mode
No signal detected
FEF generated
Greater than 2.25V
FX mode
Signal detected
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
FEF (Far End Fault), repetition of a special pattern, which consists of 84-ones and 1-zero, is generated under “FX mode with no
signal detected”. The purpose of FEF is to notify the sender of a faulty link. When receiving a FEF, the LINK will go down to indicate
a fault, even with fiber signal detected. The transmitter is not affected by receiving a FEF and still sends out its normal transmit
pattern from MAC. FEF can be disabled by strapping pin27 low, please refer to “Strapping Options” section.
Media Converter Operation
The KSZ8001 is capable of performing media conversion with 2 parts in a back-to-back RMII mode as indicated in the diagram. Both
parts are in RMII mode and with RMII_BTB asserted (pin21 & 22 strapped high). One part is operating at TX mode and the other in
FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-Negotiation on the TX side will prohibit 10BASE-T link up. Additional options can be implemented under
this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2 and TXD2 pins
need to be connected via an inverter. When TXD2 pin is high in both the copper and fiber operation, it disables transmit. Meanwhile,
the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected. TXD3 should be tied low
and RXD3 let float. Please contact your local Micrel FAE for a Media Converter reference design.
相關PDF資料
PDF描述
VE-J73-EZ-S CONVERTER MOD DC/DC 24V 25W
M3BBA-3420K IDC CABLE - MSR34A/MC34F/MSR34A
AQ10515NJ-T INDUCTOR 15NH 300MA 5% 0402 SMD
VE-J5N-EZ-S CONVERTER MOD DC/DC 18.5V 25W
UPJ1E331MPD1TD CAP ALUM 330UF 25V 20% RADIAL
相關代理商/技術參數
參數描述
KSZ8001LI 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-LQFP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8001LI TR 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-LQFP, I-Temp, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8001LIA3 功能描述:TXRX 10/100 LINKMD 3.3V 48-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC(0.154",3.90mm 寬) 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND
KSZ8001S 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-SSOP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8001S TR 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-SSOP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray