- 您現在的位置：買賣IC網 > PDF目錄11593 > KSZ8873FLL (Micrel Inc)IC ETHERNET SW 3PORT 64LQFP PDF資料下載
參數資料
| 型號： | KSZ8873FLL |
| 廠商： | Micrel Inc |
| 文件頁數： | 52/115頁 |
| 文件大小： | 0K |
| 描述： | IC ETHERNET SW 3PORT 64LQFP |
| 產品培訓模塊： | KSZ8873 Ethernet Switches |
| 特色產品： | KSZ8873 Ethernet Switch Controller |
| 標準包裝： | 160 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 576-3631 KSZ8873FLL-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
Micrel, Inc.
KSZ8873MLL/FLL/RLL
September 20, 2013
41
Revision 1.6
All the packets received on port A and transmitted on port B are mirrored on the sniffer port. To turn on the “AND”
feature, set Register 5 bit [0] to ‘1’. For example, port 1 is programmed to be “receive sniff”, port 2 is programmed to
be “transmit sniff”, and port 3 is programmed to be the “sniffer port”. A packet received on port 1 is destined to port 2
after the internal lookup. The KSZ8873MLL/FLL/RLL forwards the packet to both port 2 and port 3.
Multiple ports can be selected as “receive sniff” or “transmit sniff”. In addition, any port can be selected as the “sniffer
port”. All these per port features can be selected through Registers 17, 33, and 49 for ports 1, 2 and 3, respectively.
Rate Limiting Support
The KSZ8873MLL/FLL/RLL provides a fine resolution hardware rate limiting from 64Kbps to 99Mbps. The rate step is
64Kbps when the rate range is from 64Kbps to 960Kbps and 1Mbps for 1Mbps to 100Mbps(100BT) or to 10Mbps(10BT)
(refer to Data Rate Limit Table). The rate limit is independently on the “receive side” and on the “transmit side” on a per
port basis. For 10BASE-T, a rate setting above 10 Mbps means the rate is not limited. On the receive side, the data
receive rate for each priority at each port can be limited by setting up Ingress Rate Control Registers. On the transmit
side, the data transmit rate for each priority queue at each port can be limited by setting up Egress Rate Control
Registers. The size of each frame has options to include minimum IFG (Inter Frame Gap) or Preamble byte, in addition to
the data field (from packet DA to FCS).
For ingress rate limiting, KSZ8873MLL/FLL/RLL provides options to selectively choose frames from all types, multicast,
broadcast, and flooded unicast frames. The KSZ8873MLL/FLL/RLL counts the data rate from those selected type of
frames. Packets are dropped at the ingress port when the data rate exceeds the specified rate limit.
For egress rate limiting, the Leaky Bucket algorithm is applied to each output priority queue for shaping output traffic. Inter
frame gap is stretched on a per frame base to generate smooth, non-burst egress traffic. The throughput of each output
priority queue is limited by the egress rate specified.
If any egress queue receives more traffic than the specified egress rate throughput, packets may be accumulated in the
output queue and packet memory. After the memory of the queue or the port is used up, packet dropping or flow control
will be triggered. As a result of congestion, the actual egress rate may be dominated by flow control/dropping at the
ingress end, and may be therefore slightly less than the specified egress rate.
To reduce congestion, it is a good practice to make sure the egress bandwidth exceeds the ingress bandwidth.
Unicast MAC Address Filtering
The unicast MAC address filtering function works in conjunction with the static MAC address table. First, the static MAC
address table is used to assign a dedicated MAC address to a specific port. If a unicast MAC address is not recorded in
the static table, it is also not learned in the dynamic MAC table. The KSZ8873MLL/FLL/RLL is then configured with the
option to either filter or forward unicast packets for an unknown MAC address. This option is enabled and configured in
Register 14.
This function is useful in preventing the broadcast of unicast packets that could degrade the quality of the port in
applications such as voice over Internet Protocol (VoIP).
Configuration Interface
The KSZ8873MLL/FLL/RLL can operate as both a managed switch and an unmanaged switch.
In unmanaged mode, the KSZ8873MLL/FLL/RLL is typically programmed using an EEPROM. If no EEPROM is present,
the KSZ8873MLL/FLL/RLL is configured using its default register settings. Some default settings are configured via strap-
in pin options. The strap-in pins are indicated in the “Pin Description and I/O Assignment” table.
I
2C Master Serial Bus Configuration
With an additional I
2C (“2-wire”) EEPROM, the KSZ8873MLL/FLL/RLL can perform more advanced switch features like
“broadcast storm protection” and “rate control” without the need of an external processor.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B6J-IW-F1 | CONVERTER MOD DC/DC 36V 100W |
| VI-B6H-IW-F2 | CONVERTER MOD DC/DC 52V 100W |
| VI-B6F-IX-F4 | CONVERTER MOD DC/DC 72V 75W |
| VI-B6F-IW-F2 | CONVERTER MOD DC/DC 72V 100W |
| VI-B6D-IX-F1 | CONVERTER MOD DC/DC 85V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8873FLL-EVAL | 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 2x FX Ports - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8873FLLI | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x FX Ports (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MLL | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x MII Interface - Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MLL AM | 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x MII Interface (Automotive Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MLL AM TR | 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x MII Interface (Automotive Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。