參數資料
型號： KSZ8873FLL
廠商： Micrel Inc
文件頁數： 54/115頁
文件大?。?/td> 0K
描述： IC ETHERNET SW 3PORT 64LQFP
產品培訓模塊： KSZ8873 Ethernet Switches
特色產品： KSZ8873 Ethernet Switch Controller
標準包裝： 160
控制器類型： 以太網開關控制器
接口： MII
電源電壓： 1.8V，2.5V，3.3V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
其它名稱： 576-3631
KSZ8873FLL-ND
Micrel, Inc.
KSZ8873MLL/FLL/RLL
September 20, 2013
43
Revision 1.6
Two fixed 8-bit device addresses are used to address the KSZ8873MLL/FLL/RLL in I2C slave mode. One is for read; the
other is for write. The addresses are as follow:
1011_1111 <read>
1011_1110 <write>
The following is a sample procedure for programming the KSZ8873MLL/FLL/RLL using the I
2C slave serial bus:
1.
Enable I
2C slave mode by setting the KSZ8873MLL/FLL/RLL strap-in Pins P2LED[1:0] to “01”.
2.
Power up the board and assert reset to the KSZ8873MLL/FLL/RLL. Configure the desired register settings in the
KSZ8873MLL/FLL/RLL, using the I2C write operation.
3.
Read back and verify the register settings in the KSZ8873MLL/FLL/RLL, using the I2C read operation.
Some of the configuration settings, such as “Aging enable”, “Auto Negotiation Enable”, “Force Speed” and “Power down”
can be programmed after the switch has been started.
SPI Slave Serial Bus Configuration
In managed mode, the KSZ8873MLL/FLL/RLL can be configured as a SPI slave device. In this mode, a SPI master
device (external controller/CPU) has complete programming access to the KSZ8873MLL/FLL/RLL’s 198 registers.
Programming access includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to
the “Static MAC Table”, “VLAN Table”, “Dynamic MAC Table” and “MIB Counters”. The tables and counters are indirectly
accessed via registers 121 to 131.
The KSZ8873MLL/FLL/RLL supports two standard SPI commands: ‘0000_0011’ for data read and ‘0000_0010’ for data
write. SPI multiple read and multiple write are also supported by the KSZ8873MLL/FLL/RLL to expedite register read back
and register configuration, respectively.
SPI multiple read is initiated when the master device continues to drive the KSZ8873MLL/FLL/RLL SPISN input pin (SPI
Slave Select signal) low after a byte (a register) is read. The KSZ8873MLL/FLL/RLL internal address counter increments
automatically to the next byte (next register) after the read. The next byte at the next register address is shifted out onto
the KSZ8873MLL/FLL/RLL SPIQ output pin. SPI multiple read continues until the SPI master device terminates it by de-
asserting the SPISN signal to the KSZ8873MLL/FLL/RLL.
Similarly, SPI multiple write is initiated when the master device continues to drive the KSZ8873MLL/FLL/RLL SPISN input
pin low after a byte (a register) is written. The KSZ8873MLL/FLL/RLL internal address counter increments automatically to
the next byte (next register) after the write. The next byte that is sent from the master device to the KSZ8873MLL/FLL/RLL
SDA input pin is written to the next register address. SPI multiple write continues until the SPI master device terminates it
by de-asserting the SPISN signal to the KSZ8873MLL/FLL/RLL.
For both SPI multiple read and multiple write, the KSZ8873MLL/FLL/RLL internal address counter wraps back to register
address zero once the highest register address is reached. This feature allows all 198 KSZ8873MLL/FLL/RLL registers to
be read, or written with a single SPI command from any initial register address.
The KSZ8873MLL/FLL/RLL is capable of supporting a SPI bus.
相關PDF資料
PDF描述
VI-B6J-IW-F1 CONVERTER MOD DC/DC 36V 100W
VI-B6H-IW-F2 CONVERTER MOD DC/DC 52V 100W
VI-B6F-IX-F4 CONVERTER MOD DC/DC 72V 75W
VI-B6F-IW-F2 CONVERTER MOD DC/DC 72V 100W
VI-B6D-IX-F1 CONVERTER MOD DC/DC 85V 75W
相關代理商/技術參數
參數描述
KSZ8873FLL-EVAL 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 2x FX Ports - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8873FLLI 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x FX Ports (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLL 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x MII Interface - Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLL AM 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x MII Interface (Automotive Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLL AM TR 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x MII Interface (Automotive Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*