參數資料
型號： KSZ8993
廠商： Micrel Inc
文件頁數： 13/35頁
文件大?。?/td> 0K
描述： IC SWITCH 10/100 3PORT 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-1032
KS8993
Micrel
KS8993
20
May 2005
P1_V : (1,0,1)
P2_V : (1,1,0)
P3_V : (1,1,1)
In the above setting, there are two VLANs. VLAN 1 includes ports 1,3 and VLAN 2 includes ports 2, 3. Port 3 belongs to both
VLANs. If vmdis = 1, port 1 can never talk to port 2. Port 3 has to route all the traffic across the two VLANs. If vmdis = 0 and
there are unicast packets, all ports can talk to all others. If vmdis = 0 and there are multicast packets, those packets are confined
in the same VLAN. The router can take advantage of the “vmdis = 0” feature, acting as an agent to handle broadcast/multicast
protocol, while leaving unicast switching task to KS8993. For example, port 1 sends an “ARP” for the port 2 MAC address. Since
port 2 cannot receive the ARP, the attached router on port 3 will act as an agent and report the MAC address of port 2 to port
1. Then all the unicast traffic between port 1 and port 2 could be switched by KS8993, instead of by the router port. This
application could enable “wire speed” switching/routing. This feature is sometimes called “l(fā)eaky VLAN”. This leaky VLAN does
improve the system performance by separating broadcast domains. Note KS8993 does not support “duplicated MAC
addresses” in different VLANs to save MAC table size.
QoS Priority Support
This feature provides QoS for applications such as VOIP, video conferencing, and mission critical applications. The KS8993
per port transmit queue could be split into two priority queues, high priority and low priority queues. The splitting feature could
be optionally per port enabled (using pin Px_TXQ2). If a port is split, high priority packets will be put in the high priority queue.
If a port’s transmit queue is not split, high priority and low priority packets will be treated equally. There are four priority schemes
(selected by pins PRSEL1 and PRSEL0): (1), transmit high priority packets always before low priority packets, i.e. A low priority
packet could be transmitted only when the high priority queue is empty. (2), 10/1 ratio, transmit a low priority after every 10
high priority packets transmitted if both queues are busy. (3), 5/1 ratio, (4) 2/1 ratio. Incoming packet priority could be classified
in two ways, port-based or 802.1p.
Port based priority: Each port could be individually specified as a high priority receiving port (using pin Px_PP). All the packets
received at the high priority receiving port will be marked high priority and sent to the high priority transmit queue if the
corresponding queue is split.
802.1p based priority: 802.1p based priority could be enabled by pins Px_1PEN. KS8993 will examine incoming packets to
determine whether they are tagged and retrieve the corresponding priority information. The priority field in the VLAN tag is 3
bits wide and is compared against “priority base value specified by pins (PBASE[2:0]). If a received packet has an equal or
larger priority value than the “priority base” value, the packet will be put in the high priority transmit queue if the corresponding
queue is split. KS8993 can optionally remove or insert priority tagged frame’s header (2 bytes of tag protocol identifier 0x8100
and 2 bytes of tag control information). If a transmitting port has its corresponding Px_TAGINS set (meaning tag insertion),
the transmitting logic will automatically insert “priority tag” for untagged packets with NULL VLAN ID and its priority value (7
for high priority and 0 for low priority). For already tagged packets, KS8993 will pass the original packet without changing its
tag content. If a transmitting port has its corresponding Px_TAGRM set (meaning tag removal), the transmitting logic will
automatically remove “802.1q tag”. For untagged packets, KS8993 will pass the original packet without changing any content.
Either tag insertion or removal will cause CRC recalculation.
相關PDF資料
PDF描述
KSZ8993MI IC SWITCH 10/100 W/TXRX 128PQFP
LFEC6E-3TN144C IC FPGA 6.1KLUTS 144TQFP
LFXP3E-5T144C IC FPGA 3.1KLUTS 100I/O 144-TQFP
LFXP3E-4T144I IC FPGA 3.1KLUTS 100I/O 144-TQFP
LFXP3C-5T144C IC FPGA 3.1KLUTS 100I/O 144-TQFP
相關代理商/技術參數
參數描述
KSZ8993-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993F 功能描述:以太網 IC Single Chip Fast Ethernet Media Converter - Lead free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993F-A1 功能描述:IC CONV MED 10/100 3PORT 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8993F-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993F RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993FL 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Transceivers & TS-1000 OAM, single 3.3V supply, 128-PQFP, Lead free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*