參數資料
型號： KSZ8993
廠商： Micrel Inc
文件頁數： 8/35頁
文件大?。?/td> 0K
描述： IC SWITCH 10/100 3PORT 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-1032
KS8993
Micrel
KS8993
16
May 2005
Functional Overview: Physical Layer Transceiver
100BaseTX Transmit
The 100BaseTX transmit function performs parallel to serial conversion, 4B/5B coding, scrambling, NRZ to NRZI conversion,
MLT3 encoding and transmission. The circuit starts with a parallel to serial conversion, which converts the data from the MAC
into a 125MHz serial bit stream. The data and control stream is then converted into 4B/5B coding followed by a scrambler. The
serialized data is further converted from NRZ to NRZI format, then transmitted in MLT3 current output. The output current is
set by an external 1% 3.01k
resistor for the 1:1 transformer ratio. It has a typical rise/fall time of 4ns and complies to the ANSI
TP-PMD standard regarding amplitude balance, overshoot and timing jitters.
100BaseTX Receive
The 100BaseTX receiver function performs adaptive equalization, DC restoration, MLT3 to NRZI conversion, data and clock
recovery, NRZI to NRZ conversion, de-scrambling, 4B/5B decoding and serial to parallel conversion. The receiving side starts
with the equalization filter to compensate inter-symbol interference (ISI) over the twisted pair cable. Since the amplitude loss
and phase distortion is a function of the length of the cable, the equalizer has to adjust its characteristics to optimize the
performance. In this design, the variable equalizer will make an initial estimation based on comparisons of incoming signal
strength against some known cable characteristics, then tunes itself for optimization. This is an ongoing process and can self
adjust against the environmental changes such as temperature variations.
The equalized signal then goes through a DC restoration and data conversion block. The DC restoration circuit is used to
compensate for the effect of base line wander and improve the dynamic range. The differential data conversion circuit converts
the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then used to
convert the NRZI signal into the NRZ format. The signal is then sent through the de-scrambler followed by the 4B/5B decoder.
Finally, the NRZ serial data is provided as the input data to the MAC.
PLL Clock Synthesizer
The KS8993 generates clocks for the external MII and SNI interface based on the interface type selected.
Scrambler/De-scrambler (100BaseTX only)
The purpose of the scrambler is to spread the power spectrum of the signal in order to reduce EMI and baseline wander. The
data is scrambled by the use of an 11-bit wide linear feedback shift register (LFSR). This can generate a 2047-bit non-repetitive
sequence. The receiver will then de-scramble the incoming data stream with the same sequence at the transmitter.
100BaseFX Operation
100BaseFX operation is very similar to 100BaseTX operation with the differences being that the scrambler/de-scrambler and
MLT3 encoder/decoder are bypassed on transmission and reception. In this mode the auto-negotiation feature is bypassed
since there is no standard that supports fiber auto-negotiation.
100BaseFX Signal Detection
The physical port runs in 100BaseFX mode if FXSDx >.6V. This signal is referenced to VREFx which is set at 1/2 Vdd but can
be overridden by an external level. VREFx can be connected to the “minus” signal of a differential pair coming from the fiber
module (“plus connects to FXSDx) used to convey signal detect. When FXSDx is below .6V then 100BaseFX mode is disabled.
100BaseFX Far End Fault
Far end fault occurs when the signal detection is logically false from the receive fiber module. When this occurs, the
transmission side signals the other end of the link by sending 84 1’s followed by a zero in the idle period between frames.
Far End Fault can be disabled by setting external hardware pin TEST[2]=0 and TEST[1] = float. See
“I/O Description” for pin
description.
10BaseT Transmit
The output 10BaseT driver is incorporated into the 100BaseT driver to allow transmission with the same magnetic. They are
internally wave-shaped and pre-emphasized into outputs with a typical 2.2V amplitude. The harmonic contents are at least
27dB below the fundamental when driven by an all-ones Manchester-encoded signal.
Special note for 10BaseT operation: With an operating voltage of 2.5V, the KS8993 does not always achieve the specified
transmit voltage swing greater than or equal to 2.2V as specified by IEEE 802.3. The important factor however is that the
KS8993 does adhere to the specified receive signal voltages using the IEEE twisted pair model with a 100
load. The transmit
voltage swing can be increased to 2.2V or above by increasing the supply voltage to 2.65V if so desired.
10BaseT Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a
PLL perform the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A
相關PDF資料
PDF描述
KSZ8993MI IC SWITCH 10/100 W/TXRX 128PQFP
LFEC6E-3TN144C IC FPGA 6.1KLUTS 144TQFP
LFXP3E-5T144C IC FPGA 3.1KLUTS 100I/O 144-TQFP
LFXP3E-4T144I IC FPGA 3.1KLUTS 100I/O 144-TQFP
LFXP3C-5T144C IC FPGA 3.1KLUTS 100I/O 144-TQFP
相關代理商/技術參數
參數描述
KSZ8993-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993F 功能描述:以太網 IC Single Chip Fast Ethernet Media Converter - Lead free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993F-A1 功能描述:IC CONV MED 10/100 3PORT 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8993F-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993F RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993FL 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Transceivers & TS-1000 OAM, single 3.3V supply, 128-PQFP, Lead free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*