參數資料
型號: KSZ8993MLI
廠商: Micrel Inc
文件頁數: 16/86頁
文件大?。?/td> 0K
描述: IC SWITCH 10/100 3PORT 128-PQFP
標準包裝: 66
系列: *
產品目錄頁面: 1081 (CN2011-ZH PDF)
其它名稱: 576-3350
Micrel, Inc.
KSZ8993M/ML
October 2008
23
M9999-020606
10BASE-T Transmit
The output 10BASE-T driver is incorporated into the 100BASE-T driver to allow transmission with the same
magnetic. They are internally wave-shaped and pre-emphasized into outputs with a typical 2.3V amplitude. The
harmonic contents are at least 27dB below the fundamental when driven by an all-ones Manchester-encoded
signal.
10BASE-T Receive
On the receive side, input buffers and level detecting squelch circuits are employed. A differential input receiver
circuit and a PLL perform the decoding function. The Manchester-encoded data stream is separated into clock
signal and NRZ data. A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths in
order to prevent noises at the RXP or RXM input from falsely triggering the decoder. When the input exceeds the
squelch limit, the PLL locks onto the incoming signal and the KSZ8993M decodes a data frame. The receiver
clock is maintained active during idle periods in between data reception.
Power Management
The KSZ8993M features a per-port power down mode. To save power, the user can power down ports that are
not in use by setting the port control registers, or MII control registers. In addition, there is a full chip power down
mode. When activated, the entire chip will be shut down.
MDI /MDI-X Auto Crossover
The KSZ8993M supports MDI/ DI-X auto crossover. This facilitates the use of either a straight connection CAT-5
cable or a crossover CAT-5 cable. The auto-sense function will detect remote transmit and receive pairs, and
correctly assign the transmit and receive pairs from the KSZ8993M device. This feature can be extremely useful
when end users are unaware of cable types and can also save on an additional uplink configuration connection.
The auto-crossover feature can be disabled through the port control registers.
Based on the IEEE 802.3 standard, the MDI and MDI-X definitions are as follows:
MDI
MDI-X
RJ45 Pins
Signals
RJ-45 Pins
Signals
1
TD+
1
RD+
2
TD-
2
RD-
3
RD+
3
TD+
6
RD-
6
TD-
Table 2. MDI/MDI-X Pin Definitions
相關PDF資料
PDF描述
KSZ8993ML IC SWITCH 10/100 W/TXRX 128PQFP
KSZ8995FQ IC SWITCH 10/100 5PORT 128-PQFP
KSZ8995MA IC SWITCH 10/100 5PORT 128PQFP
KSZ8995MI IC SWITCH 5-PORT 10/100 128PQFP
KSZ9021GN TR TXRX ETHERNET GB GMII/MII 64MLF
相關代理商/技術參數
參數描述
KSZ8995FQ 功能描述:以太網 IC Integrated 5-Port Switch with Fiber on Port 3 & 4, Lead free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8995FQ-EVAL 功能描述:以太網開發工具 Integrated 5-Port Switch with Fiber on Port 3 & 4 Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8995FQI 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8995M 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8995MA 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray