參數資料
型號： L6701TR
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： 1.5 A SWITCHING REGULATOR, 110 kHz SWITCHING FREQ-MAX, PDSO36
封裝： LEAD FREE, SSO-36
文件頁數： 33/44頁
文件大?。?/td> 627K
代理商： L6701TR
Obsolete
Product(s)
- Obsolete
Product(s)
L6701
16 Layout Guidelines
39/44
16.2
Small Signal Components and Connections
These are small signal components and connections to critical nodes of the application as well
as bypass capacitors for the device supply (See Figure 20). Locate the bypass capacitor (VCC
and Bootstrap capacitor) close to the device and refer sensible components such as frequency
set-up resistor ROSC to SGND. Star grounding is suggested: connect SGND to PGND plane in
a single point to avoid that drops due to the high current delivered causes errors in the device
behavior.
VSEN pin filtered vs. SGND helps in reducing noise injection into device: take care in routing
driving net for this pin in order to minimize coupled noise.
Remote Buffer Connection must be routed as parallel nets from the FBG/FBR pins to the load
in order to avoid the pick-up of any common mode noise. Connecting these pins in points far
from the load will cause a non-optimum load regulation, increasing output tolerance.
Locate current reading components close to the device. It's also important to minimize any
offset in the measurement and, to get a better precision, to connect the traces as close as
possible to the sensing elements.
Caution:
Boot Capacitor Extra Charge. Systems that do not use Schottky diodes might show big
negative spikes on the phase pin. This spike can be limited as well as the positive spike but has
an additional consequence: it causes the bootstrap capacitor to be over-charged. This extra-
charge can cause, in the worst case condition of maximum input voltage and during particular
transients, that boot-to-phase voltage overcomes the abs. max. ratings also causing device
failures. It is then suggested in this cases to limit this extra-charge by:
–
adding a small resistor in series to the boot diode (one resistor can be enough for all
the three diodes if placed upstream the boot diode anode, see Figure 20)
–
using non-capacitive boot diodes (such as standard diodes).
Figure 20. Power connections and related connections layout (same for all phases).
L
CIN
VIN
UGATEx
PHASEx
LGATEx
PGNDx
LOAD
BOOTx
PHASEx
VCC
SGND
+Vcc
C
BOOT
L
CIN
VIN
LOAD
To limit C
BOOT
Extra-Charge
相關PDF資料
PDF描述
L6712DTR 2 A SWITCHING CONTROLLER, PDSO28
L6712Q 2 A SWITCHING CONTROLLER, QCC36
L6712ADTR 2 A SWITCHING CONTROLLER, PDSO28
L6712D 2 A SWITCHING CONTROLLER, PDSO28
L6712QTR 2 A SWITCHING CONTROLLER, QCC36
相關代理商/技術參數
參數描述
L6706 制造商:STMicroelectronics 功能描述:DC DC Cntrlr Single-OUT Step Down 40-Pin VFQFPN EP Tray 制造商:STMicroelectronics 功能描述:HANDHELD & COMPUTER PM - Trays 制造商:STMicroelectronics 功能描述:8-Bit VR11.1 Single CTRL w/int Driver
L6706TR 功能描述:DC/DC 開關控制器 VR11.1 SINGLE PHASE CNTRL W/INT DRI RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6709 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6709TR 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6710 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*